Sign in perhaps register 。

The advantage of the reinforcement mesh system is ecological. It is filled with natural stone materials. There is a gap between the stone materials to allow plants to grow in it. It can also plant plants on it. It has the dual effects of engineering slope protection and plant slope protection. The Ecological Grid mat is a combination with a height of cm ~ cm

What are the uses of I-beam?So why is the alloy pipe easy to rust after being pickled and passivated by the software?Burrell, mostly a multi grid box separated by spacer mesh.All the cracks occur at -mm away from the edge below the alloy pipe, and the macroeconomic orientation is vertical to the cold rolling orientation, showing a 'high mountain' shape.Farshut,Requirements of alloy tubes for low and medium pressure boilersH-beam is a widely used profile in steel structure buildings. It is different from I-beam. The first is the flange, and the second is that the inner surface of the flange has no inclination, and the upper and lower surfaces are parallel. The section characteristics of H-beam are obviously better than those of traditional I-beam, channel steel and angle steel. Hot push hole diameter. More sensitive applications and facilities of such methods require simplicity, low cost, easy maintenance, durable economic development and convenient product specification transformation. For example, elbow and similar products. You only need to add some spare parts. The expansion method of hot push can be used to process and manufacture large-diameter, thick wall and thin alloy steel pipes, and can not exceed the working capacity of thick wall pipes of machinery and equipment.

At the same height, light I-beam has narrower legs, thinner waist and lighter weight than ordinary I-beam. No. - is large I-beam, and No. - is medium I-beam. Imported I-beam shall be marked with actual specifications, dimensions and relevant standards. In order to ensure the welding quality of pipes, welders shall be trained, the welder should consider the operation skills. The pipe welding process may include several postures of overhead welding, vertical welding and overhead welding (when the pipe cannot rotate). The size of current should be selected to take into account the formation of vertical welding and overhead welding (some pipes are not very large, and the current cannot be adjusted in the middle of one formation). In the process,BurrellQuotation of I-beam cold bending machine, the stability and formation of arc should be controlled, It can swing properly, and the forming shall be well combined with the necessary swing.Application characteristics of I-beam:supply,→ compared with general section steel, it has the advantages of low cost, high precision and small residual stress. It does not need expensive welding materials and weld detection, and saves about % of the manufacturing cost of steel structure.Advantages of using I-beam: reduce maintenance cost, reduce downtime, improve equipment operation rate,BurrellCustom welded pipe manufacturer, reduce wear, reduce equipment capacity and increase power consumptionWhen it is used for ground heating and hot spring transportation, it can meet the requirements of refrigeration and achieve the practical effect of less damage. It is applicable to water conservancy engineering, mining and other industries to meet the provisions of cold, cold and corrosion prevention. In addition, the chemical raw material transmission pipeline has a wide indoor space.

When selecting I-beam in structural design, reasonable I-beam shall be selected according to its mechanical properties, chemical properties, weldability and structural size.Quality Assurance,Alloy pipes are widely used in building materials, and the test standards of alloy pipes are also different. Alloy pipe has high hardness and can be used at many levels, most of which is prestressed reinforcement. Where plastic deformation is not specified but compressive strength is specified,When selecting I-beam in structural design so it is flexible.Methods of exerting efficiency in application of C-section steelBurrell, reasonable I-beam shall be selected according to its mechanical properties chemical properties,BurrellA335p92 American standard high pressure alloy pipe, weldability and structural size.When selecting I-beam in structural design, reasonable I-beam shall be selected according to its mechanical properties, chemical properties, weldability and structural size.Whether I-section steel is ordinary or light, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members.