Sign in perhaps register 。

　　Many people do not know much about the packing and sealing of equipment because of the equipment of mass and energy. Next, let&#;s learn about the packaging and sealing method of the equipment: packing sealing is very common in submersible slurry pumps. This method has good sealing performance, is easy to use, and effectively reduces the wear of the host and anti vibration kinetic energy　　 When stopping the operation of the submersible slurry pump, close the cock of the vacuum gauge and pressure gauge and the gate valve on the water outlet pipeline, and After that, cut off the power supply of the motor. If the temperature of the environment is low, open the square plug at the lower part of the pump body to remove the remaining water to avoid frost cracking. During operation the maximum temperature of the bearing shall not exceed ℃,KutnaholaCarbon steel explosion-proof pipeline pump, and the quantity of calcium base grease used for lubricating oil bearing shall be the same as that of the bearing bodyKutnahola,　　Actually, you don&#;t have to worry about this. First of all, stainless steel has very strong anti-corrosion ability compared with products that are easy to rust. When many friends buy stainless steel deep well pumps, their manufacturers will apply a thin anti-corrosion coating on the outer layer of the equipment according to the needs of consumers. as　　In order to ensure the demand for water and electricity for production and living, many units, it and the generator naturally become popularSan-Juan,　　The purpose is to inject liquid higher than . MPa from the water seal ring to prevent gas leakage into the pump when the suction inlet of the submersible slurry pump is in a vacuum state. When the water pressure in the pump is higher than . MPa, the sealing fluid .-. MPa higher than the pressure in the pump can be injected to seal and reduce leakage　　Whether the pump is evacuated or overflowed, etc., and handle it at any time.　　Some corrosive pastes containing crystals can also be transported. In the application range of slurry pump, about % are used in concentrators in the mining industry. Due to the poor working conditions of primary ore dressing, the service life of slurry pump in this section is generally low. Of course, different minerals, abrasion

　　For example, concentrate and tailings are treated in the concentrator, ash and slag are removed from the power plant, slime and dense medium coal are transported in the coal preparation plant, and slurry is transported in coastal river mining operations. The weight concentration of the treated slurry is: mortar %, ore slurry %; It can be operated in series according to the needs of users.　　In this way, the upper guide housing is installed in turn. After the pump is installed, take out the gasket, tighten the pull nut evenly, and then rotate the electric pump from the coupling. The rotation must be uniform.　　 if the removed gasket is seriously damaged,　　 If the hot water within ℃ is recommended, the hot water pump must be used, and the external tap water shall be connected for cooling during operation, otherwise the motor will not be burned due to too high medium temperature.　　No matter what type of slurry pump you need, Ritter pump will provide you with high-quality slurry pump products; New progress in submersible slurry pump technology in recent years The diving depth has increased from meters to meters!　　Superior complete protection s, reasonable structure, convenient installation and high cost performance. In case of sudden power failure of the plant and emergency, the water pump will automatically start to supplement the pipe network pressure.

　　Then there are new structures, such as thermohydrodynamic seals,　　The fruit is also bad; When the axial flow pump is used, its water output is relatively large, but the head is not too high, so the effect of using the submersible slurry pump in many plain areas is also relatively good; The water output and head of the mixed flow pump are actually derived from one　　 total depth of well or pool M　　The above is the correct sequence of impeller disassembly of submersible slurry pump. Because different types of pumps have some differences in structure, we also need to refer to the instructions when disassembling.Kutnahola,　　The use of water pumps is related to all aspects of our life. With the arrival of the May Day holiday the water consumption will increase. Therefore, it is necessary for us to choose a suitable water pump.　　In fact, when the submersible slurry pump is blocked during use, it will not only have a certain impact on the working efficiency of the equipment during operation, but also cause serious damage to the equipment itself, so it is also a reminder that we are using it too　　Causes: there is air or gas accumulation in the water inlet pipe of the pump, or the bottom valve is not closed tightly, the water supply is not satisfied, the packing of the vacuum pump leaks seriously, and the gate valve or flap valve is not closed tightly.