Sign in perhaps register 。

The key purpose of grinding and polishing alloy pipe is to moisten the surface, the moment of inertia of the two main axes of the section is quite different, which makes it very limited in the scope of application. The use of I-beam shall be selected according to the requirements of design drawings.Limoges, The vertical of the processed reinforcement bar shall be divided into small sections as required.When we carry out different projects, we must use different raw materials, which can ensure the quality of the project. In many kinds of data, alloy pipe is widely used. In many projects, we will apply it, so it is very popular in the field. When people carry out the construction of alloy pipe project, there are many things that must be paid special attention to. Let&#;s take you to know:TandirClassification introductionI-beam is a kind of economical section steel with better section mechanical properties. Its characteristics are as follows:The shape of I-beam is similar to that of H-beam. What is the difference between them?

Advantages of using I-beam: reduce maintenance cost,LimogesHow much is 50 galvanized pipe, reduce downtime, improve equipment operation rate, reduce wear, reduce equipment capacity and increase power consumptionHow to judge the quality of seamless pipe?The shape of small longitudinal crack on the surface of alloy pipe is less than mm The overall width is less than mm The depth is lower than .mm.Quotation sheet,Alloy pipe can be divided into round steel pipe and special-shaped steel according to different cross-sectional area. Because the circular area is large on the premise of the same side length, a large amount of liquid can be transported with an annular tube. In addition, when the circular cross section bears the internal or external axial working pressure, the bearing force is more symmetrical. Therefore, most seamless steel pipes are round steel pipes.Precision cold rolling of small and medium-sized bearing sleeves with alloy tubes can greatly improve material utilization, bearing performance and service life. This paper systematically introduces the development of high quality cold drawn bearing steel pipe and its application in bearing. Precision cold rolling of small and medium-sized bearing sleeves with bearing steel pipes can greatly improve material utilization, bearing performance and service life. This paper systematically introduces the service life of high quality cold drawn bearings.The utility model has the advantages that the axial force of the roll is small, the axial movement is small, the working inclined plane is not required, the pass occupies a small length of the roll body and more passes can be matched under the condition of a certain length of the roll body.

H-section steel is an economic section high-efficiency profile with more optimized section area distribution and more reasonable strength weight ratio. It is named because its section is the same as the English letter 'H'. There is no slope on the inner side of the two outer edges of H-section steel, which is straight. This makes the welding and splicing of H-section steel simpler than I-section steel, better mechanical properties per unit weight, and can save a lot of materials and construction time.Welcome calls ,The side length of I-beam is small and the height is large, so it can only bear the force in one direction.There are many processes in the process of welded pipe processing, and every detail needs our attention. Welded pipes need to be treated by various processes before application. Heat treatment of welded steel pipe is an important link in the process of welding steel pipe. Hot working is a metal hot working process in which metal materials are heated, insulated and cooled in a certain medium, without high carbon steel and high chromium alloy pipe. The aqueous solution contains % sodium cyanide % ~ % (volume ratio), the solution temperature is ~ ℃,Limoges2205 duplex steel welded pipe, and the solution time is min.Limoges,All the cracks occur at -mm away from the edge below the alloy pipe, and the macroeconomic orientation is vertical to the cold rolling orientation, showing a 'high mountain' shape.Ways to obtain surface compressive stress characteristics of alloy tubesWhether I-section steel is ordinary or light, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application. I-beam is widely used in buildings or other metal structures.