Sign in perhaps register 。

　　 To ensure the efficient operation of the submerged slurry pump, the clearance between the impeller and the front guard plate must be adjusted regularly to keep it between (.-mm). In addition to monitoring the flow and pressure during the operation of the pump, the motor shall not exceed the rated current of the motor. Monitor oil seal and bearing at any time　　The non service life of the equipment is not as long as possible. If it is not used for a long time, it will not only easily corrode the parts, but also reduce the service life of the parts.Veron ,　　 If the deep well pump is not used continuously after running in the well, it should be started up once a week and run for - minutes to prevent the electric pump from being started due to corrosion.　　Some of them are OK. For irrigation and other purposes, in fact, we choose to use larger flow. Let&#;s take a look at the method of selecting pumps.Santa Ana, it can only be opened or closed, and the action time when opening and closing is relatively short.　　The mixing impeller and other main flow passage parts are made of high wear-resistant materials, which are wear-resistant, corrosion-resistant, non clogging and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more thorough desilting. No auxiliary vacuum pump is required and the investment is lower. nothing

　　Then it can enter into the volute pump housing. Then in the volute pump casing, the medium slows down because the flow channel is also gradually expanding.　　 WQ submersible sewage pump adopts a unique single or double vane impeller structure, there is also a disadvantage of using the auxiliary impeller sealing system and can effectively pass through times the diameter of the pump and solid particles with a diameter of about % of the diameter of the pump.　　However,Veron Submersible pump can pump sewage, that is, it takes some energy on the auxiliary impeller of the submersible slurry pump, which is generally about %. However, as long as the planning is reasonable, this part of the lost flow can be reduced. The slurry pump is mainly applicable to electric power, metallurgy and coalRecommendation and consultation,　　 First of all, we need to know that submersible pumps generally operate in water. In fact, most of the pumps are suitable for conveying some relatively clean media, and their impellers are generally in a closed state. However one of the media conveyed by sewage pumps may　　However, there is also a disadvantage of using the auxiliary impeller sealing system, that is, it takes some energy on the auxiliary impeller of the submersible slurry pump, which is generally about %. However, as long as the planning is reasonable, this part of the lost flow can be reduced. The slurry pump is mainly applicable to electric power, metallurgy and coal　　 The standby submersible slurry pump shall roll the shaft / turn every week to make the bearing uniformly accept the static load and external oscillation. The building structure in the water pump room shall be reconstructed. Sound absorbing and isolating plates shall be installed around the wall and on the top of the machine room and fixed with light steel keel; The connecting holes between the machine room and other rooms are tightly blocked,

　　Submersible slurry pump In addition, it must be used continuously during transportation. If there is an interval in the middle, it must be avoided that the interval is relatively long,Veron ZD slurry pump,　　When using the submersible slurry pump, we should do a good job in all aspects of commissioning and precautions. We also need to do a good job in protecting the equipment parts and some parts of the motor. Only in this way can we avoid the impact of water and other impurities entering the motor　　The rotation direction of QW (WQ) submersible non blocking sewage pump after connection is counterclockwise from the water inlet. Assuming that the electric pump rotates, it is only necessary to adjust the wiring direction of any two wires in the cable.　When using the submersible slurry pump, the equipment may be burned out. The main reason for this phenomenon is improper operation. How should we prevent the burning out?Veron 　　It can also be used for cooling and lubrication. Once the temperature in the water pump is too high, the pump shall be stopped immediately for maintenance. Otherwise, the excessive temperature will not only affect the wear of small parts inside the equipment, but also seriously affect the working efficiency of the equipment. So what is the reason for the high temperature of the equipment　　 If the power cord is not well contacted, it will also lead to the burning of the motor.　　So it has a process of water diversion and exhaust. There are usually two ways to inject water into equipment. One is to directly inject water into the pump chamber, and the other is to pump out the gas in the pump to establish a certain vacuum and introduce the water source.