Sign in perhaps register 。

Galvanized pipe is a kind of light thin-walled steel pipe with hollow square section also known as steel cold-formed profile. It is a section steel with square section shape and size, which is made of Q hot-rolled or cold-rolled strip or coil as the base material, cold bending and high-frequency welding. In addition to wall thickness thickening, the corner size and edge flatness of hot rolled extra thick wall galvanized pipe reach or even exceed the level of resistance welding cold formed galvanized pipe. Good comprehensive mechanical properties, weldability, cold and hot workability and corrosion resistance,Besanson UniversityHot dip galvanized welded pipe manufacturer, and good low temperature toughness.Heating surface tubes for low and medium pressure boilers (working pressure is generally not greater than MPA and working temperature is below ℃);SirahaIts heat sealing effect is remarkable. It can be directly buried immediately, which can not only save resources, but also reduce consumption, not occupy the natural environment, but also purify the environment. The transportation of gas can meet the requirements of long-distance transportation, prevent actual operation and maintenance, meet the requirements of thermal insulation and cold protection, reduce heating equipment, and reduce the construction cycle time of the project. On the whole, there are many passivation methods for alloy tubes, the common ones are high temperature passivation or sodium cyanide passivation. The defects can be removed by grinding with sand wheel, but the remaining wall thickness must be within the allowable standard.

Performance parameters and application scope of I-beamWhen the beam width is small, the reinforcement shall be bent. Frame line cracktarget,The specification of pass design I-beam is expressed in cm of waist width. For example,Besanson UniversityHow much is 6 meters of one inch galvanized pipe, the waist width of No. I-beam is. The types of I-beam include hot-rolled ordinary I-beam, light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~, expressed as No. ~ No., and the inclination of inner wall of leg is : The pass system of rolled I-beam includes direct pass system, I-beam can also adopt special rolling method.The side length of I-beam is small and the height is large, so it can only bear the force in one direction.H-section steel belongs to high-efficiency and economic cutting profile (other cold-formed thin-wall section steel, profiled steel plate, etc.). Due to the reasonable section shape, they can make the steel give more play to its performance and improve the cutting capacity. Different from ordinary I-type, the flange of H-section steel is widened, and the inner and outer surfaces are usually parallel, so it is convenient to connect with other components with high-strength bolts. Its size composition is reasonable, series and models are complete, which is convenient for setting

The key purpose of grinding and polishing alloy pipe is to moisten the surface, and the relevant limit accuracy or appearance change is not easy to change.Industry management,Besanson University45 small diameter seamless pipe,Using alloy pipe to produce ring parts can improve the utilization rate of raw materials, simplify the production and manufacturing process, and save raw materials and production and processing construction time, such as roller bearing ring throwing Nowadays, seamless steel pipe has been widely used to produce hydraulic jack sleeve.During the construction of building wall, cracks and hollows show that the construction materials are unqualified, the construction at the matrix junction is not in place, and the construction personnel are poor. The external wall plastering adopts electric welding steel wire mesh which can prevent cracking and strengthen the wall.Passivation treatment operation of alloy pipeBesanson University,Using alloy pipe to produce ring parts can improve the utilization rate of raw materials, simplify the production and manufacturing process, and save raw materials and production and processing construction time, such as roller bearing ring throwing Nowadays, seamless steel pipe has been widely used to produce hydraulic jack sleeve.Due to the unique performance of I-beam, I-beam has successfully solved the problem of serious equipment wear in many industries.The pickling agent in the pickling process contains many acidic substances, including hydrochloric acid, sodium cyanide, etc., which has strong corrosion and reduction, and the temperature of etching substances is relatively high. Therefore, the corrosion resistance of alloy pipes is specified higher.