Sign in perhaps register 。

Some reasons for product composition ratio: in order to reduce the production cost, reduce the proportion content of some important elements such as chromium and nickel, and increase the content of other elements such as carbon. This production phenomenon that the composition ratio is not strictly in accordance with the product model and product characteristics not only greatly reduces the product quality, for example, when the chromium content of stainless steel pipe is insufficient it not only affects the production The corrosion resistance and formability of products have potential product quality and safety hazards when they are used in chemical, equipment and production industries. At the same time, they also affect the appearance and oxidation resistance of products.Austenitic stainless steel austenitic stainless steel is developed to overcome the lack of corrosion resistance and brittleness of martensitic stainless steel. The basic composition is crl% and Ni%, which is referred to as - steel for short. Its characteristic is that the carbon content is less than .%, and the single-phase austenite structure is obtained by the combination of Cr and Ni.Saint-Denis,However,Saint-DenisOcr19ni9ti stainless steel plate, some people will still communicate online or by telephone to ask whether the stainless steel pipe we produce can be used as a water pipe. Series & mdash; Heat resistant chromium alloy steel.Shihung,Model & mdash; It has better temperature resistance.Application: utility boiler industry, mainly in key parts such as high temperature section of superheater and reheater.Add a small amount of sulfur and phosphorus to make it easier to cut.

Welding, high frequency preheating plus three torch argon arc welding, high frequency preheating plus plasma argon arc welding. The progress of combined welding is very significant. As for the combined welding of steel pipe with high-frequency preheating, the welding operation is complex, and the whole welding is easy to complete automation. This combination is easy to connect with the existing high-frequency welding equipment, with low investment cost and good benefit.The cold working process performance and cold forming performance are much better than that of ferritic stainless steel.Stainless steel pipe can be divided into equal section pipe and variable section pipe according to the profile shape. Variable section pipes include conical pipes, stepped pipes and periodic section pipes.Statistics,When the stainless steel fixed port is welded, it will be difficult to ventilate on both sides of the weld. At this time, how to ensure the argon filling protection on the inner side of the weld has become a difficult problem. For a long time, facing the national high price the reasonable price and perfect service of all kinds of stainless steel plates, stainless steel coils, stainless steel belts and stainless steel pipes have been recognized by the majority of customers. In the actual construction on site, we use two welding joints The above problems were successfully solved by plugging with water-soluble paper on the side, ventilation from the weld center and sealing with adhesive tape on the outside (see Table ). Series & mdash; Martensitic precipitation hardening stainless steel.. It is our responsibility not to pay attention to the maintenance of the pipe during transportation, mix the pipe with corroded chemical commodities, or soak the two water into the packaging film during transportation in rainy days, which will cause rust. . It is the responsibility of the processor and manufacturer. When cutting stainless steel or iron when manufacturing goods, the scrap iron will cause rust on the surface of the steel pipe. Therefore,Saint-DenisStainless steel seamless pipe, it is only reasonable for highly skilled technicians to deepen investigation and discussion, make a reasonable division of responsibilities and who should be responsible for whose achievements. You can't let steel mills, pipe factories, processors, or users bear the liability for compensation!

During welding, the process of ventilation in advance and gas stop behind shall be adopted, and the adhesive cloth on the outside shall be torn off while welding. Because the blocking plate is composed of rubber and white iron sheet, it is not easy to be damaged, so this welding can well ensure that the inner side of the weld is filled with argon and its purity,Model & mdash; Commonly used precipitation hardening stainless steel model, usually also called -; %Cr,%Ni.The external anti-corrosion coating of stainless steel shall be galvanized and epoxy asphalt coating or coating with higher requirements according to the soil conditions of the pipe laying ground.The corrosion resistance is the same,Saint-DenisStainless steel pipe door, and the strength is better because the carbon content is relatively high.Saint-Denis,Meet the needs of architects and structural designers.After molten steel casting, stainless steel pipe fittings generally adopt the same vertical, the ladle to be poured is transferred above the tundish mouth through the rotary table, and then the molten steel is tundish through the long nozzle. The molten steel in tundish enters the mold through the submerged nozzle for forming, condensation and continuous downward movement.Model & mdash; High strength cutting tool steel, with slightly higher carbon content, can obtain higher yield strength after appropriate heat treatment, and the hardness can reach hrc. It belongs to hard stainless steel. A common application example is & ldquo; Shaving blade & rdquo;. There are three common models: C and f (easy to process).