Sign in perhaps register 。

serumCorrosive pipeline pump, it has a great impact on the impeller of the equipment itself. So how to detect whether the equipment has cavitation during use?serum

　　Water flow into the bearing damages the bearing.　　For example,　　 Damage of mechanical seal the material of mechanical seal is generally Cr or L, which is relatively rigid,serumCarbon steel explosion-proof pipeline pump, not flexible and vulnerable. The installation of mechanical seal is that the static ring is fixed outside, and the moving ring is fixed with the pump shaft. When the slurry pump reverses, and the impeller retreats　　The above is a brief introduction to the effect and form of shaft seal of submersible slurry pump. Users can choose the appropriate shaft seal type according to their actual needs.Shuto Orizari,　　Submersible slurry pump is a kind of pump that can adapt to various working conditions and can treat various sewage from environmental protection industry. Let&#;s take a look at the maintenance measures for the accessories of the submersible slurry pump.　　The vertical sand pumping pump is popular with a wide range of sand pumping pump users because it is easy to move. This equipment is made of high-tech endurance data. Its service life has been greatly improved, and the maintenance frequency has been reduced the cost has been reduced, and the income has been increased.　　 for screws that are too tight or rusted for a long time, the nut can be lubricated with kerosene prepared in advance, or the nut can be gently knocked with a wooden hammer and then removed. This method can also be used in slurry pumps and other places.

　　According to the user&#;s requirements, the motor can add a variety of protection devices such as water inflow detection and overheating, so that the product can operate safely for a long time under adverse working conditions.　　The sheath is divided into front sheath and rear sheath, which are made of natural rubber. The lining is made of high chromium alloy, so it has good wear resistance. It can be used until it is worn out, so as to prolong the maintenance and replacement cycle and reduce the operation cost. The outlet of this series of pumps can be installed at angles　　To repair the equipment. Submersible slurry pump is a machine used to transport liquid. It can be divided into many types according to different transport media. Then, when transporting some media with special properties, the equipment will be treated with corrosion-resistant and wear-resistant process. Only in this way can the equipment be improvedInterpretation and observation,　　The above is the correct sequence of impeller disassembly of submersible slurry pump. Because different types of pumps have some differences in structure, a new gasket shall be replaced. The removed parts shall be cleaned with kerosene before assembly.

　　The first stage impeller of the pump is disassembled; It is also necessary to screw down the connecting nut between the water absorption section and the bearing body and the bolt on the bearing pressure connection, so that it is convenient for us to disassemble the bearing parts; When the shaft is pulled out from the suction section, the fixing nut on the shaft shall beassets,　　The above is about how to replace the water seal of Boshan submersible slurry pump. In addition to the water seal,serumDrilling fluid slurry pump, other parts of the pump also need to be replaced in time when they are damaged. Moreover, some parts of the pump are relatively easy to be damaged, so we need to replace them regularly during use　　Check whether it needs to be replaced.　　There is no suction line. As the water storage tank is not deep enough and the suction pipe of the water pump is not deep enough, the inlet pipe of the water vortex is not deep enough. Water with a lot of gas. Destroy all normal water Self-priming pumps. To ensure sufficient depth of digestion and absorption of low watermark water. At that time, lift the submersible slurry pump and move it to the adjacent position of the previous sand pumping place to continue pumping sand, so as to move the sand pumping place back and forth for sand pumping, so that the sand pumping area in this area forms a honeycomb,serum,　　 The rotor assembly is designed according to the actual situation, and the operation is more stable!　　In the application of pumps, the first thing we think of is water. Whether it is drinking water or coefficient water, even the polluted water in cities needs to be purified. All these require its equipment to provide services for us. Without pumps, our basic survival is a problem.　　 In addition, the use of ° and S-shaped bends should be reduced as much as possible during the installation and design of pipelines.