Sign in perhaps register 。

　　 The slurry pump mainly aims at conveying flow, so the flow meter (meter) shall be installed in the operation monitoring system as far as possible to monitor whether the flow meets the requirements at any time; In the pipeline system, slag flushing system and pressure filtration dehydration system equipped with hydrocyclone, certain　　 If the hot water within ℃ is recommended, the hot water pump must be used, and the external tap water shall be connected for cooling during operation, otherwise the motor will not be burned due to too high medium temperature.Vibel,　　The treatment method is as follows: first,VibelVertical heavy-duty slurry pump, check the circuit voltage to reduce the speed of the water pump.　　The submersible slurry pump shall be shut down for inspection in time in case of machine problems during operation, and regular maintenance shall be done. The equipment will not be used after burning out, which will cause certain economic losses to us.Tchamba,　　Circumference. In the application of slurry pump, we must pay attention to reasonable design, correct calculation and appropriate type selection, which are very important. In addition to the main wheel, a set of stirring impeller is added at the bottom of the product, which can spray the precipitated slag into a mixture of water and solid particles　　Under the action of auxiliary devices, it can transport the slurry, it can also ensure the internal and external balance of the submersible slurry pump during transportation, so that the pressure at both ends of the equipment can be balanced during normal use　　Ordinary vertical motor can be used without waterproof while the motor shaft and pump shaft of submersible slurry pump are coaxial, so the motor must be waterproof and sealed and the motor and pump can be immersed in liquid at the same time; The vertical slurry pump is an early product,VibelSelf priming slurry pump wholesale, and the submersible slurry pump is a newly developed product according to the market demand

　　Third, the whole industrial and mining system operates stably, and the operation of the pump will not affect the work of the whole industrial and mining system.　　Damage to the rotor.　　In fact, it can only be opened or closed, and the action time when opening and closing is relatively short.Application process　　How to avoid this situation when the equipment is in use.　　 Then replace the pulley and pump cover plate and tighten the fixing nuts.　　It is not correct that it has no effect on us.

　　There is a difference between submersible slurry pump and sewage pump. Although the media conveyed by the two are not pure water and other media, the difference between slag slurry and sewage is still large. Let&#;s take a look at the difference between the two.Marketing Department,　　The hardened mud layer collapses after softening, avoiding the phenomenon of burying the pump during use.　　 The subsequent operation noise of the slurry pump increases. Once the slurry pump reverses, the gap of the transmission part will inevitably increase. If it is not carefully adjusted, great noise may occur in the later operation process, which is caused by the friction between the impeller, replace it with a new one.Vibel,　　When the slurry pump is working, the pump needs to be placed on land, the suction pipe in water, and the pump needs to be started. Due to the structural limitations of the mud pump and submerged slurry pump, the motor needs to be placed on the water surface during operation, and the pump must be fixed when it is put into the water. Otherwise, the motor will fall into the water　　Where ρ—— Density of transmission medium liquid (kg/m; γ—— Gravity of medium liquid (n/m; H -- pump lift (m); Q - water pump flow (m/s); G - gravitational acceleration (m/s.　　The difference between the shaft power P and the effective power PE is the power loss in the pump, which is measured by the pump efficiency. The pump efficiency is the ratio of the effective power and the shaft power, which is measured by η Indicates.　　Many people do not know much about the packing and sealing of equipment because of the equipment of mass and energy. Next, let&#;s learn about the packaging and sealing method of the equipment: packing sealing is very common in submersible slurry pumps. This method has good sealing performance, is easy to use