Sign in perhaps register 。

Remove the flame. If the filler metal does not melt, continue to heat the joint and try again. The melted filler metal is sucked into the casing port according to the capillary effect until a complete filler metal ring appears on the casing port. Remove the flame Pay special attention not to let the flame directly contact the filler metal. It should be the heat at the joint that melts the filler metal. In order to clean the copper pipe, the welding flux must have a degree of corrosivity, and shall be cleaned after brazing. The so-called & quot; self-cleaning& quot; fluxes are generally not recommended because of their corrosivity.In August, the price of domestic medium and heavy plates fell sharply. As of August , the price center of ordinary carbon boards in leading cities had dropped to , down yuan/ton from the end of July. At the beginning of the month, affected by the macro bad news, and the recent poor performance of fundamentals the market mentality turned to pessimism, and some traders shipped at low prices. The market inventory rose, the inventory pressure was high, the stock shortage phenomenon disappeared, and the market transaction atmosphere was cold, the demand performance continued to decline, and the spot price fell under pressure.Luena ,When the copper tube is heated and the flux melts into liquid, place the preheated electrode on the welding point immediately. As soon as the electrode begins to melt, move the flame nozzle back and forth until the solder flows into the gap between the two tubese the flame, let the solder contact the welding point, and then remove it after a few seconds. If it is suspected or found that there is still a gap between the two pipes. It can be heated again to make the flame nozzle move continuously at two points. A small amount of solder can be added.The room temperature tensile strength of the annealed red copper sheet is ~ kgf/mm, the elongation is ~%,The second of the five application fields of red copper plate T, red copper row and red copper tube: copper is widely used in the chemical industry to manufacture vacuum vessels, distillation pots, brewing pots, etc.The copper tube shall be heated and welded first, and then the joint shall be heated until the heated part turns dark red. At this time, when the filler metal contacts the tube, the filler metal shall melt.In consideration of the above factors, more and more steel plants have stopped production since October, and the production limit in Wu an and Tangshan heating seasons has been advanced. In addition, the formal implementation of production limit in & quot; +& quot; urban heating seasons after November by steel enterprises, the demand for iron ore in the future is likely to further deteriorate. The iron ore inventory of the steel plant is relatively high, and the willingness to further replenish the inventory is not strong. In terms of supply, the fourth quarter is generally the peak period for the shipment of imported ores. Although the production of domestic mines has been reduced due to environmental protection,Luena Stainless steel plate, the quantity of * * * is relatively limited. In general, and the low-temperature pipeline in the oxygen production equipment can also be used. Some relatively thin copper tubes can be used to transport some pressurized liquids, and can also be used as pressure measuring tubes in instruments; In addition, the copper pipe is relatively firm, unlike other metals, which are easily corroded, so now many water pipes and refrigeration pipes used in buildings will choose to use the copper pipe.Welding sequence of copper pipe Before heating, apply the flux to the position to be welded.If you want to avoid this kind of situation for a long time, you can choose passivation treatment. In this way, not only is the copper surface serious, it can be cleaned under normal circumstances, but it is not a big problem to keep it in the air for one year or more after ultrasonic treatment and immersion treatment, so this effect is very good.Quality risk,Red copper inventory may end the trend of continuous decline. With the increase of production restriction of steel enterprises and the pressure of demand, the continuous decline of iron ore port inventory may end. In addition, according to the new statistics of * *, the available days of imported iron ore of steel mills are days, which is one day lower than that before the National Day, and is on the high side of history. The steel mill said that at present the iron ore inventory basically meets the production requirements. Considering the future production reduction and restriction, the steel mill is not willing to replenish the inventory.The production method of soft copper tube is basically the same as that of hard copper tube, that is, the annealing process is added compared with the hard copper tube. Annealing of copper tubes means that they are calcined in a high temperature furnace to change the arrangement of the elements in the copper tubes. However after annealing, the copper tubes will become soft, which makes it easier to bend. The copper tubes produced in this way are called soft copper tubes.Today, the price of tube billets is up and down. At present, Jiangxin hot rolling is yuan, continuous casting yuan is down yuan, Dongfang hot rolling yuan is down yuan, Luli hot rolling yuan is down yuan, Tiangang hot rolling an is down yuan, production is stopped in mid January, Weigang hot rolling yuan is up yuan continuous casting yuan is up yuan, Huaigang yuan is up yuan, Changqiang yuan,Luena Aluminum rod, Linggang yuan.

This week (-, the market price of red copper bar rose, and the transaction was not ideal. On the bidding day of Shagang last weekend, the price was stable to support the market, and the rising of billets at the weekend drove the market up in a wave, and the price of variety wire rods also rose by yuan at the weekend. However, it was reported that the deal was very poor which led to the price being s table for the next two days. Until Wednesday, due to the negative outlook on the future market and the reduction of steel billets in the afternoon spiral diving, Xinji rose yuan on the rd; For the future market, the off-season is coming, the demand is weakening and the market wait-and-see mood is getting stronger. But when winter comes, the environmental protection inspection is becoming more and more strict, which supports the market. It is expected that the price ofety wire rod will be adjusted in a weak way in the short term.Home page recommendation,Advantages and scope of application of copper tube ground heating At present, ground heating is not only a comfortable heating method, but also a symbol of modern life quality. More and more houses, public buildings, sports facilities, industrial facilities and other places begin to use ground heating radiator, which is an important part of ground heating. Due to the corrosion resistance of copper, copper tubes are selected as the main material of radiator in many places.When the purity of pure copper is higher, the corrosion resistance is better. Copper pipes processed with recycled copper are easy to cause corrosion due to impurities inside. (I) Problems that should be noted in copper pipe welding are generally %. % % or % silver electrode shall have good fluidity and be assisted by flux. The flux used shall be a flexible mixture or powder, with carbonization flame for copper pipe welding.In the middle and late ten days, although there were good news such as the rise of futures and the increase of production restriction policy in Wu an region, due to the high inventory level, most of them had shipped goods, and spot prices lacked motivation to rise. The market inventory rose significantly. At that time,Luena Stainless steel welded pipe, the market inventory in Handan reached a high level after the festival. The sluggish demand performance for a long time led to the oversupply of the market, and the continuous rise of inventory led to the empty market mentality.Luena ,In addition, it is not easy to be corroded and can adapt to various environments. It can be used normally at low and high temperatures, so copper pipes need to be selected for many times in other places.Generally, the overall order receiving quantity of Tianjin Hebei Henan Plate Plant was not ideal. According to the monitoring data, the overall order intake of medium and heavy plate mills in Tianjin Hebei Henan region in the first ten days of May remained stable and weak. Due to the weak market shock, the overall order intake of the spot steel market was relatively weak. The total quantity of orders received in the first ten days of May is only about tons, while at the end of April, the total quantity of post settlement agreements of main steel plants can exceed tons.