Sign in perhaps register 。

The lifting stage can provide real-time information on the operation of the entire vehicle, and improving the reliability and safety of the system. The definition of safety zone is very important because the lifting stage has a large range of movements, and it must be accurately calculated. The lifting stage has two structurally separate systems, the ground turntable and the high-altitude work bar. However, for various movements on the vehicle, it is also an interconnected system, which needs to consider the priority of operation, system redundancy, and safety assurance of actions.Check the wear and clearance condition of the guide wheel of the cargo elevatorKosenza,The safety control voltage of is selected with rolling guide shoes, high accuracy, wear resistance, and stable lifting. The characteristics of the Jinchuang lifting platform are as follows: . There is no need for a machine room above the shaft. . The hydraulic elevator is not equipped with a counterweight device to improve the utilization rate of the shaft area. . The load and load cylinder of the hydraulic elevator directly act on the foundation pit, and the strength requirements of the shaft are low, Brick or brick concrete structure hoistway can be used for Jinchuang lifting platform safety and stability advantages. Overflow valve: It can prevent system pressure from being too high during upward movement. Emergency manual valve: In case of power failure, it can make the elevator emergency descend to the nearest floor position and open the door.Please refer to the instruction manual for the maintenance and maintenance of the elevator to check the braking torque of the brakeHaderslev,Clean and inspect the crown wheel frame assembly, correct or replace with new partsWhat are the functions of anti rust primer for warehouse cargo elevators?Manganese steel is generally used as the primary profile for warehouse cargo elevators. In order to achieve better anti-corrosion effect, a layer of rust resistant primer is usually applied, which effectively blocks air and prevents premature corrosion of the steel. Below, Ruilong hydraulic press will explain the role of rust resistant primer.

　　?? Hidden danger investigation relies on joint efforts from all aspects:?? Construction enterprises are the main responsibility for identifying hidden dangers in construction elevators. They should strengthen daily inspections and regular inspections, and carefully inspect the steel structure, safety protection devices, electrical devices, and transmission devices of construction elevatorsThe second method is the protective layer method, which covers the metal surface of the aluminum alloy lifting platform with a protective layer to isolate the metal products from the surrounding corrosive medium and prevent corrosion. Apply engine oil petroleum jelly, paint, or cover the surface of steel parts with corrosion-resistant non-metallic materials such as enamel and plastic; It is not easy to apply a layer of electroplating, hot plating, etc. on the surface of steelAfter cleaning, clean the filter and replace it with a new filter element before adding new oil. What adverse reactions may occur during the early use of hydraulic cargo elevators?Free consultation,Clean and inspect the crown wheel frame assembly, correct or replace with new partsCheck the interlocking equipment, up and down travel, and other safety maintenance switches of the cage door and fence doorCheck the relative orientation between the cable support wall and the cable guide frame

Check the relative orientation between the cable support wall and the cable guide frameoriginal,Please refer to the instruction manual for the maintenance and maintenance of the elevator to check the braking torque of the brakeJinchuang lifting platform product feature is mainly used for high-altitude cargo transportation between floors. With a load capacity of - tons and a lifting height of - meters a guide rail elevator, also known as a hydraulic elevator, can be installed indoors and outdoors. The lifting height is high and uses a side mounted oil cylinder,KosenzaMobile hydraulic boarding bridge, which runs smoothly, has low noise, is convenient for maintenance, and has a long service life. In case of power outage, manual emergency descent can be used, which is safe,KosenzaHow much is the guide rail hydraulic lifting platform, convenient fast, and practical. The pit depth is generally cm-cm, and the top layer height is not affected, The pump station can be customized according to the on-site environment, suitable for - floors of steel structures or concrete factories. Both the internal and external parts can be used. The pump station adopts a joint venture pump station and an imported pump station from Italy. If the speed requirement is too high, a joint venture customized pump station can be used to meet the ideal delivery requirements. The oil cylinder and seals are made of imported components, solving the problem of unstable oil pressure for customers, The oil leakage problem of components . The oil cylinder is built into the platform . The heavy-duty steel wire rope wheel or weighted special chain ensures safety . The automatic insurance during the lifting process ensures vehicle safety . The synchronous device during the lifting process ensures that the vehicle may not overturn . The alarm setting before falling to the ground ensures the safety of the operator . The chain or steel wire rope fracture protection device . The hydraulic system pressure loss explosion-proof protection device . The elevator special flat permanent magnet switch is selected, The leveling effect is good. . The distance between heavy and empty loads is small, and the leveling accuracy is high. . Standard elevator boards, LCD display call boxes, relevant wiring harnesses, and connectors are selected. Beautiful appearance, visual display of the position of the elevator car on the floor, wiring harness connected using connectors, check the adjustment and fixation status of the counterweight guide wheel. Check the balancing equipment of the steel wire rope,KosenzaFully automatic scissor fork lifting platform, the crown wheel and the counterweight steel wire rope bracketKosenza,On the contrary, it should be adjusted in the opposite direction; When the meshing backlash of the gear pair is greater than .mm, loosen the connecting nut of the eccentric shaft of the guide roller and the tooth back pressure wheel as shown in , adjust the tooth back pressure wheel to press towards the back plane of the gear rack until the backlash reaches a reasonable range. Otherwise, it should be adjusted in the opposite direction. At this point, the guide roller should be loosened for o and then adjusted according to the adjustment of the guide roller.Ensure that the small gear and pressure wheel are securely fastened on the drive base plate, and check the fixing condition of the drive base plate boltsPlease refer to the instruction manual for the maintenance and maintenance of the elevator to check the braking torque of the brake