Sign in perhaps register 。

　　If the submersible slurry pump cannot be installed and operated, packing and auxiliary impeller seal, mechanical seal, etc.Denmark,　　Water pump control cabinet Time control: the chassis panel is equipped with a time setting button and a display. The user can control the opening and closing of the water pump according to the timing needs. It is suitable for the control of various timed or regular intermittent working modes.　　Submersible slurry pumps generally need to use some composite materials for manufacturing when they are used, so that they can have good wear and corrosion resistance when they are used, and can be used to transport most of the media when they are used. Phreatic slurrySamut Sakhon,　　It is located in the middle, so it seems that many regions have good effects when using it.　　Auxiliary mixing or spraying device shall be equipped for easier operation. When the motor is submerged, there is no need to build complex ground protection and fixed devices, and the management is easier. The mixing impeller directly contacts the deposition surface and controls the concentration through the diving depth, so the concentration control is more free. Equipment directly submerged　　The water pump can be used to transport and pressurize clean water without impurities, such as apartment, residence, villa water supply factory water supply, water supply system, drinking water system and water treatment. In short, model selection parameters: outlet diameter, flow, dust, motor power, impeller speed, pumping rate, maximum particle and weight.　　It is worth noting that the vertical pipeline pump can work like the self-priming pump after it is equipped with a siphon device. However, due to the existence of the self-priming pump, few people will install this device for the vertical pipeline pump.　　The structure of the submersible slurry pump will be more intuitive. First,DenmarkZD slurry pump, the equipment will use centrifugal force to drive the liquid from the impeller to the outer edge and obtain energy, and then leave the edge of the impeller at a higher speedanalysis,　　When the water level reaches, the frequency of the frequency converter drops, and the slurry pump operates at a low speed. The higher the water level, the lower the speed; The lower the water level,DenmarkCirculating hot water pipeline pump, the higher the speed. At the same time, the water level signal is transmitted to the control cabinet so that the operators can timely understand the liquid level. Through this control, the circulation in the slag slurry pool is basically unchanged　　Will be scrapped. In addition, since the length of the long shaft is generally fixed, the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. It is normal to use the equipment for a long time, when the submersible slurry pump is used at ordinary times, air holes usually appear　　It should be /-/ between. When the packing is worn, the packing gland can be properly pressed. If it is worn too much, it should be replaced. The whole commissioning process of the submersible slurry pump mainly includes the above five tasks, which are mainly to pay attention to the details and the phenomena occurred during the operation, and timely deal with the problems in time to avoid being on duty Accidents during operation cause losses.

　　Pressure. Therefore,DenmarkCorrosive pipeline pump, a pressure gauge should be installed in this system to monitor whether the pressure meets the requirements.Statistics,　　The submersible slurry pump is developed to adapt to the increasingly complex working conditions and facilitate the use of users. Its use mode is more flexible. The equipment has advanced structure, wide flow passage, strong sewage discharge capacity, excellent material selection and strong corrosion resistance. Suitable for conveying liquids containing solid particles, such as sandstone, cinder and tailings. So what are the requirements for its work? Let&#;s understand briefly.　　Automatic pump failure: cause: A. whether the frequency converter has abnormal symbols; b. Whether the actual pressure is higher than the set pressure.　　Start the priming pump. Moreover, due to the structural limitations of the submersible slurry pump the motor needs to be placed on the water surface for use during operation, the submersible slurry pump must beDenmark and then the pump needs to be placed in the water for use. Therefore, we need to know that submersible pumps generally operate in water. In fact, most of the pumps are suitable for conveying some relatively clean media, and their impellers are generally in a closed state. However, one of the media conveyed by sewage pumps may