Sign in perhaps register 。

　　Reasonable.　　It can also be used for cooling and lubrication. Once the temperature in the water pump is too high, the pump shall be stopped immediately for maintenance. Otherwise, the excessive temperature will not only affect the wear of small parts inside the equipment, but also seriously affect the working efficiency of the equipment. So what is the reason for the high temperature of the equipmentBrasia,　　Friends who are more concerned about this issue can dispel their concerns.　　Submersible slurry pump is a kind of pump that can adapt to various working conditions and can treat various sewage from environmental protection industry. Let&#;s take a look at the maintenance measures for the accessories of the submersible slurry pump.Kangdong-up,　　 When adding lubricating oil to the pump at ordinary times the metering must be controlled, model selection parameters: outlet diameter and the excess lubricating oil in the pump must be discharged and replaced regularly.　　Fourth, flow, dust, impeller speed, pumping rate, maximum particle and weight.　　Reasonable.

　　Adjustment. When using the submersible slurry pump, accessories will be used and some auxiliary measures will be taken to improve the overall performance of the equipment and ensure the stable use of the equipment. Many users do not pay attention to these things when using them, which will cause equipment problems and affect work efficiency. So we&#;re using　　Work to prevent the electric pump from overheating and damage. The technical guidelines for laboratory construction in medical institutions (Trial Implementation) directly proposed that stainless steel should be used. Compared with the technical code for construction of biosafety laboratories (gb-, copper pipes and non-toxic plastic pipes are no longer proposed.　　 Then tighten the compression nut on the packing gland evenly to make the liquid leak out in drops, and pay attention to the temperature rise outside the packing chamber.Quality inspection report,　　 selection of flow: single suction pump or double suction pump shall be selected according to the flow; single suction pump or multi suction pump shall be selected according to the lift.　　The above is the correct sequence of impeller disassembly of submersible slurry pump. Because different types of pumps have some differences in structure, we also need to refer to the instructions when disassembling.　　Water or air leakage in the pipeline. The nut may not be tightened during installation. If the leakage is not serious, the air or water leakage can be treated with cement or cement slurry mixed with asphalt oil. Temporary repairs can be done with some wet mud or soft soap. If water leaks at the water pump joint, tighten the nut with a wrench. as

　　 The difference between the vertical slurry pump and the submersible slurry pump The working position of the vertical slurry pump is different. The vertical slurry pump is partially immersed in the pit and cannot be completely immersed in the liquid level. The submersible slurry pump can be completely immersed (including the motor part) below the liquid level; Use of motor for vertical slurry pumpCreate brilliance, the use of ° and S-shaped bends should be reduced as much as possible during the installation and design of pipelines.　　Finally, select the appropriate pump model according to the determined Q and H. It should be noted that in the actual selection,BrasiaSingle stage slurry pump, in principle, the pump model closest to the intersection of the pump performance curve and the device performance curve should be selected, and the best operating point of the pump should be in the high-efficiency area of the pump efficiency curve as far as possible.　　The fruit is also bad; When the axial flow pump is used, its water output is relatively large, but the head is not too high,BrasiaVertical slurry pump,BrasiaDeep well pump, so the effect of using the submersible slurry pump in many plain areas is also relatively good; The water output and head of the mixed flow pump are actually derived from oneBrasia,　　Many users, including new practitioners of slurry pumps, often fail to distinguish the difference between submerged vertical slurry pumps and submerged slurry pumps. The names of submerged and submerged slurry pumps seem similar, but there are essential differences. What is the difference between submersible slurry pump and vertical slurry pump?　　Although the shaft seal occupies a small position in the pump, the normal operation of the pump is closely related to the shaft seal.　　So it has a process of water diversion and exhaust. There are usually two ways to inject water into equipment. One is to directly inject water into the pump chamber, and the other is to pump out the gas in the pump to establish a certain vacuum and introduce the water source.