Sign in perhaps register 。

　　In the application of pumps, the first thing we think of is water. Whether it is drinking water or coefficient water, even the polluted water in cities needs to be purified. All these require its equipment to provide services for us. Without pumps, our basic survival is a problem.　　 Then tighten the compression nut on the packing gland evenly to make the liquid leak out in drops, and pay attention to the temperature rise outside the packing chamber.Charlotten,CharlottenZD slurry pump,　　The liquid level of slurry shall be higher than the inlet of pump.　　As a submersible slurry pump widely used in many fields, it has the advantages of simple structure, convenient disassembly and maintenance, and convenient installation and use. The change of the sealing structure of the pump avoids the direct damage to the bearing after the mechanical seal is damaged, and the service life of the bearing has also been greatly changed.Nahavand,　　 add water with manual pump. Some pump owners have their own hand pumps. They can also buy or manufacture their own small hand pumps. The gate valve shall be installed at the water inlet. After closing the valve, inject a small amount of water into the water compressor to divert water. When the hand pump discharges water it means that the pump is full　　The two have certain commonalities. They are both submersible. As the name suggests, but generally speaking the pump is in an invasive state when running. The submersible slurry pump is a kind of submersible pump, people often say that the submersible pump refers to the clean water pump, such as the submersible pump for domestic water and farmland irrigation and pumping　　Pump. In addition, the submersible slurry pump is mainly characterized by 'slurry', which is wear-resistant and particle passing.

　　Do a good job of fixing to avoid the motor falling into the water and directly scrapping.　　Microcomputer controller LW light: cause: the light is on and the machine stops, the water level is low, the water level returns to normal, and the machine starts automatically.　　When using the submersible slurry pump, we should do a good job in all aspects of commissioning and precautions. We also need to do a good job in protecting the equipment parts and some parts of the motor. Only in this way can we avoid the impact of water and other impurities entering the motorWelcome calls , the slurry pump has high operation efficiency and low loss.　　 install the front pump shaft first and then the rear bearing for the slurry pump of the filter press of the cylindrical bearing box.　　How to disassemble the submersible slurry pump and how to assemble it after disassembly. The technical points and precautions for disassembly will be introduced to avoid disassembly, pump damage and disassembly.

　　The input quantity is related to many factors such as the rotating speed of the submersible slurry pump, the bearing standard, the continuous working time, the number of stops and starts of the pump, the surrounding environment and the working temperature. Therefore, it is necessary to gradually accumulate the experience and add smooth oil in a reasonable and timely manner.market price　　 drainage and water injection with vacuum equipment: the self exhaust of centrifugal pump is the same as the negative pressure exhaust of vacuum pump, it is necessary to put the electric pump into clean water and run it for several minutes to prevent sediment in the pump and ensure the cleanness of the electric pump.　　It should be /-/ between. When the packing is worn,CharlottenVortex pump and pipeline pump, it should be replaced. The whole commissioning process of the submersible slurry pump mainly includes the above five tasks, which are mainly to pay attention to the details and the phenomena occurred during the operation,CharlottenSubmersible sewage pump, and timely deal with the problems in time to avoid being on duty Accidents during operation cause losses.Charlotten,　　 repair and level the welding part of the submersible slurry pump with a file, clean the part to be bound with alcohol again and wipe it dry.　　Slurry pump Inappropriate model is selected when selecting the pump. In actual use, when the load conditions do not match the model of the slurry pump, for example, the pump lift used is too high or too low, which will lead to overload, so we are selecting the pump　　It is occasionally found that there is insufficient liquid supply when using, so what are the reasons for this situation and how to deal with it.