Sign in perhaps register 。

　　 Cutting blades can be selected to cut some large block solid substances into pieces during use, so that blockage can be avoided during reuse.　　Moreover, the leaked flammable, explosion and poisoning, and the consequences will be unimaginable.Sibo,　　In fact,SiboCarbon steel explosion-proof pipeline pump, it is easy to distinguish whether a submersible sewage pump is a submersible pump or a sewage pump. A submersible sewage pump is both a submersible pump and a sewage pump,SiboLong shaft submerged slurry pump, because it is designed to pump sewage or other media. Its usage is to use it in water. Both names are acceptable. When　　The disc friction loss of the slurry pump impeller will decrease with the decrease of the impeller diameter, so that the pump efficiency of most low specific speed pumps will improve slightly after the impeller is cut. After cutting, keep the blades overlapped to a certain extent, and the degree of blade overlap will decrease with the addition of specific speedTomsk,　　Avoid airborne sound transmission; Ensure the airtightness of machine room doors and windows. The water pump is equipped with a sound proof cover, and an exhaust fan is added inside the cover to ensure the ventilation of the equipment. At the same time, the inlet and outlet of the sound proof cover are equipped with silencing equipment. A vibration isolation platform is installed at the bottom of the water pump for foundation vibration reduction to isolate the vibration generated during the operation of the water pump　　 repair and level the welding part of the submersible slurry pump with a file, clean the part to be bound with alcohol again and wipe it dry.　　The premise of using this method is that the water gun must have sufficient flow during use, otherwise the effect of the submersible slurry pump may not be obvious.

　　The above four methods can be used to detect whether the submersible slurry pump has cavitation, because if the equipment is in use, it will also have a certain impact on other parts of the equipment. Sometimes submersible slurry pump　　During installation, check whether the installation position conforms to Chinese standards, and select the installation height according to the specific suction lift. The horizontal pipeline centrifugal pump was not filled with sufficient water before it was started. There is a certain amount of air in the pipeline, which reduces the vacuum degree of the pipeline pump and affects the suction lift. Water inlet pipe　　 When the power supply voltage is too low, the pump will be overloaded, because the pump is also widely used in many rural watering. In this case, so the current in the stator winding will also beanalysis,　　It needs to be replaced in case of damage, swelling and deformation, insufficient spring pressure breakage, etc.　　Wheel, mixing impeller and other main flow passage parts are made of high wear-resistant raw materials, which are wear-resistant, corrosion-resistant, non clogging, and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more complete desilting. There is no need to equip auxiliary vacuum pump and the investment is lower.　　It will burn out. If there is a heating problem in use, you can refer to the following reasons.

　　 Assembly of rotor parts of submersible slurry pump Before assembly apply a layer of lubricating oil on the mounting surface to protect the shaft hole from damage.management,　　The structure of the submersible slurry pump will be more intuitive. First, the equipment will use centrifugal force to drive the liquid from the impeller to the outer edge and obtain energy, and then leave the edge of the impeller at a higher speed　　 There are many reasons for motor overheating. It may be because the power supply voltage is too high, or there is a problem with the water pump or the motor itself.　　Generally, the diving depth of the submersible slurry pump is not more than meters, and the operation is reliable. Why not more than meters? This is the crucial technical point of the submersible slurry pump, because the current sealing technology in China is more than meters, not because the slurry pump has a problem, but becauseSibo,　　Yes,SiboSmall deep well pump, such mechanical faults will cause the stator winding of the pump to be burnt out.　　Yes, such mechanical faults will cause the stator winding of the pump to be burnt out.　　 repair and level the welding part of the submersible slurry pump with a file, clean the part to be bound with alcohol again and wipe it dry.