Sign in perhaps register 。

　　Will be scrapped. In addition, since the length of the long shaft is generally fixed the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. The submersible slurry pump is developed to adapt to increasingly complex working conditions and facilitate the use of users. Its use mode is more　　The motor is scrapped. Moreover, the installation and use of the pump is troublesome, and the application occasions are subject to many restrictions.Janakala,　　Replace the motor shaft of the water pump.　　 The fixing method of the impeller is changed from screw thread to key clamp to prevent the impeller from falling off and causing damage!Birkirkara,　　 Move the sand pumping site frequently. When the pump pumps sand at a fixed position and drops to a certain height, lift the submersible slurry pump and move it to the adjacent position of the previous sand pumping place to continue pumping sand, so as to move the sand pumping place back and forth for sand pumping,JanakalaBaigang deep well pump, so that the sand pumping area in this area forms a honeycomb　　Second, the power used is not matched, so the motor temperature will be too high after long-term overload operation; In addition, frequent startup during use will also lead to fever, so I　　Compared with the vertical slurry pump, the application market is also larger. In addition to the existing industrial and mining applications of the vertical slurry pump, the submersible slurry pump can also be used as a mobile slurry pump, such as sand pumping on board, prospecting, etc; Submersible slurry pump assembly workshop III. what are the advantages of submersible slurry pump

　　 install the front pump shaft first and then the rear bearing for the slurry pump of the filter press of the cylindrical bearing box.　　Reliability and bearing capacity, extending the service life of the pump.　　If there are sundries blocked, the pump will not be filled with water. When this happens again, technicians need to properly adjust the liquid level in the pump sump to a proper height, and check the impeller. In case of damage or aging it needs to be replaced in time,Latest quotation,JanakalaDrilling fluid slurry pump,　　When the slurry pump is working, the pump needs to be placed on land, the suction pipe in water, and the pump needs to be started. Due to the structural limitations of the mud pump and submerged slurry pump, the motor needs to be placed on the water surface during operation, and the pump must be fixed when it is put into the water. Otherwise, the motor will fall into the water　　Submersible slurry pump In addition, the sewage pump is usually driven by a motor, so in fact, it can be adjusted to a certain extent during use. The submersible slurry pump needs to use a line when in use　　Superior, complete protection s, reasonable structure,JanakalaWater well pipeline pump, convenient installation and high cost performance. In case of sudden power failure of the plant and emergency, the water pump will automatically start to supplement the pipe network pressure.

　　So it is called: submersible slurry pump.how much,　　 To ensure the efficient operation of the submerged slurry pump, the clearance between the impeller and the front guard plate must be adjusted regularly to keep it between (.-mm). In addition to monitoring the flow and pressure during the operation of the pump, the motor shall not exceed the rated current of the motor. Monitor oil seal and bearing at any time　　It can be divided into single slurry suction pump and double slurry suction pump; The second is that the slurry pumps can be classified according to the pump shaft and horizontal position of the slurry pump: horizontal slurry pump and vertical slurry pump. The horizontal slurry pumps of Panshi pump are mostly ah, AHR, and the cavitation allowance of the device shall be greater than that of the pump. It is recommended to use the reverse charging installation method when transporting residues with high weight concentration.Janakala,　　The above four methods can be used to detect whether the submersible slurry pump has cavitation, because if the equipment is in use, it will have a great impact on the operating efficiency. Even if the cavitation time is long, it will also have a certain impact on other parts of the equipment. Sometimes submersible slurry pump　　Friction. Because if the surface of the pump is smooth when it is used, the equipment will consume less energy when it is used. Generally, the submersible slurry pump and impeller are sprayed with polymer composite materials for use　　Do a good job of fixing to avoid the motor falling into the water and directly scrapping.