Sign in perhaps register 。

　　The structure of the submersible slurry pump will be more intuitive. First, the equipment will use centrifugal force to drive the liquid from the impeller to the outer edge and obtain energy, and then leave the edge of the impeller at a higher speed　　As a submersible slurry pump widely used in many fields, it has the advantages of simple structure, and convenient installation and use. The change of the sealing structure of the pump avoids the direct damage to the bearing after the mechanical seal is damaged, and the service life of the bearing has also been greatly changed.Neville,　　The horizontal slurry pump is a cantilever centrifugal slurry pump, which is suitable for conveying abrasive or corrosive slurry. The structures of all types of horizontal slurry pumps are similar except that the pump head (including pump body, pump cover, impeller, etc.) has different structures. The pump head part, shaft seal part and transmission part　　How to avoid this situation when the equipment is in use.Sibut,　　 Then unscrew the nut at the front end of the pump shaft, remove the cover plate,NevilleSmall deep well pump, and press out the middle impeller and water seal.　　Yes, industrial pumps have also increased in recent years.　　 We also need to make choices according to local conditions when we make purchases at ordinary times. For example, the head of the centrifugal pump itself is relatively high, but its water output is not very large when it is used, so it is effective when it is used in many mountainous areas

　　Auxiliary mixing or spraying device shall be equipped for easier operation. When the motor is submerged, there is no need to build complex ground protection and fixed devices, and the management is easier. The mixing impeller directly contacts the deposition surface and controls the concentration through the diving depth, so the concentration control is more free. Equipment directly submerged　　 The reasons for excessive power loss are as follows: the running speed of the screw rod is too high.　　 If it is found that the impeller is damaged and the liquid supply is insufficient, it is necessary to replace the new impeller in time for use.Highly recommended,NevilleCarbon steel explosion-proof pipeline pump,　When using the submersible slurry pump, the equipment may be burned out. The main reason for this phenomenon is improper operation. How should we prevent the burning out?　　In recent years, the demand for submersible slurry pumps has increased greatly. In many fields, submersible slurry pumps have replaced vertical slurry pumps. What are the differences between the two? Let&#;s yze.　　The equipment is integrated with the oil cooler, with compact layout. The water pump meets the modular and integrated design requirements of diesel engine parts. The joint surface with oil cooler adopts rubber sealing method, which has good sealing effect. Submersible slurry pump is a kind of solid-liquid mixing medium with the help of centrifugal force

　　Submersible slurry pump it fills the gap in the application of slurry pump. When the submergence is deep and there is no good mud outlet,NevilleWater well pipeline pump, that is, the traditional slurry pump cannot be installed and operated and the submersible slurry pump can supplement this part of the blank work point.technological innovation,　　The hardened mud layer collapses after softening, avoiding the phenomenon of burying the pump during use.　　Submersible pump: as the name suggests, the whole pump (with motor) needs to be in the slurry.　　If there is a standby pump, it is better to use two pumps in turn. If the pump is stuck, the pump can only be repaired. A net can be added at the water inlet to prevent too many impurities from entering the pump. In this way, the probability of pump sticking will be much smaller!Neville,　　The purpose is to inject liquid higher than . MPa from the water seal ring to prevent gas leakage into the pump when the suction inlet of the submersible slurry pump is in a vacuum state. When the water pressure in the pump is higher than . MPa the sealing fluid .-. MPa higher than the pressure in the pump can be injected to seal and reduce leakage　　After understanding the working principle of the submersible slurry pump, we will also know that those parts are prone to wear during normal use. In this way, so as to improve the integrity of the equipment and　　Fourth, model selection parameters: outlet diameter, flow, dust motor power, impeller speed, pumping rate, maximum particle and weight.