Sign in perhaps register 。

　　It will generate heat, but when it is serious, it will directly burn out the insulation; There may also be some faults in the ventilation system. At this time it is necessary to check whether the fan of the submersible slurry pump is damaged or rotating　　If the submersible slurry pump cannot be installed and operated, the blank operation point can be supplemented.Bissell,　　The actual operating flow is too large, resulting in the following results: when the flow increases, the shaft power of the pump increases, while the efficiency of the motor remains unchanged, which may cause heating or even burn out the motor　　Third, the whole industrial and mining system operates stably, and the operation of the pump will not affect the work of the whole industrial and mining system.Datong City,　　If the shaft seal is not properly selected it will not only require frequent maintenance during operation, but also leak a large amount of transmitted liquid.　　 The slurry pump mainly aims at conveying flow, so the flow meter (meter) shall be installed in the operation monitoring system as far as possible to monitor whether the flow meets the requirements at any time; In the pipeline system, slag flushing system and pressure filtration dehydration system equipped with hydrocyclone, certain　　The installation of submersible slurry pump is a step that needs to be concerned. Since we all care about it, it is mainly because the installation will directly affect the use effect. The installation work should be seamless. Some key operating points can be seen when installing the slurry pump.

　　Normal operation. The submersible slurry pump can transport the slurry with corrosive or solid particles, coal slurry heavy medium transportation and dredging the river. When the equipment is pumping sand, some sand layers around the equipment will make the equipment covered by a large amount of sediment, we should choose　　Correct the main shaft of the water pump and adjust the position of the water pump and the motor relatively.　　It is occasionally found that there is insufficient liquid supply when using, so what are the reasons for this situation and how to deal with it.Test conclusion,　　The water pump can be used to transport and pressurize clean water without impurities, such as apartment,BissellNon clogged pipeline sewage pump,BissellPipeline pump body, residence, villa water supply, factory water supply, water supply system, drinking water system and water treatment. In short, there are many uses.　　It will generate heat, but when it is serious, it will directly burn out the insulation; There may also be some faults in the ventilation system. At this time, it is necessary to check whether the fan of the submersible slurry pump is damaged or rotating　　 One frequency converter with one slurry pump is adopted for installation. The specific transformation method is as follows: close the return valve, adopt the water level closed-loop control mode, install the liquid level sensor on the inner wall of the tank by the manufacturer of the slurry pump, and use the PID adjustment of the frequency converter. When

　　Second, the service life of the flow passage parts of the pump is relatively long, saving production costs.market,　　 It may also be because the pump&#;s liquid supply pipe is blocked by other substances during normal use.　　Work to prevent the electric pump from overheating and damage. The technical guidelines for laboratory construction in medical institutions (Trial Implementation) directly proposed that stainless steel should be used. Compared with the technical code for construction of biosafety laboratories (gb-, copper pipes and non-toxic plastic pipes are no longer proposed.　　 Structural features and working principle qsz submersible slurry pump is a coaxial integration of water pump and motor. During operation, and transmits energy to the slurry medium to generate a certain flow rate, drive the solid flow, and realize the transportation of slurry.Bissell　　 First of all, let&#;s understand the causes of insufficient liquid supply: If the liquid level stored in the circulating liquid storage tank is lower than %, then insufficient liquid supply will occur when it is in use. Or the pump adds too much lubricating oil, which leads to accumulation　　The high-efficiency slurry pump has three characteristics: first,BissellSewage pump diving, the slurry pump has high operation efficiency and low loss.　　Then there are new structures, such as thermohydrodynamic seals, backup seals and asymmetric molded metal single wall bellows seals.