Sign in perhaps register 。

The shape of small longitudinal crack on the surface of alloy pipe is less than mm The overall width is less than mm The depth is lower than .mm.However,LarissaAlloy pipe GH2132, what we need to do now is to improve the production technology level of China&#;s production process of C-section steel, it is more conducive for C-section steel manufacturers to produce C-section steel products suitable for truck industry.Larissa,Installation of galvanized pipe and precautionsDifference and application description between H-beam and I-beamCiudad Guayana,Function of I-beam: where is I-beam mainly used?Nitriding: also known as nitriding, it is the process of penetrating nitrogen atoms into the surface layer of steel. At present, gas nitriding is widely used in the production of alloy steel pipe.The specification of pass design I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is. The types of I-beam include hot-rolled ordinary I-beam, light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~, expressed as No. ~ No., and the inclination of inner wall of leg is : The pass system of rolled I-beam includes direct pass system, cross pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.

With the development of steel structure buildings, only I-beam is not enough, that is, thickened I-beam, which is easy to lose stability for load-bearing columns. After the above process, the next step is the polishing process of stainless steel pipe. There are network standards for internal and external wall finishing of pipelines, and the internal and external surface finishing of pipelines meets the mirror standard (i.e. sanitary standard).Nitriding: also known as nitriding, it is the process of penetrating nitrogen atoms into the surface layer of steel. At present, gas nitriding is widely used in the production of alloy steel pipe.Safety production,I-beam is widely used in buildings or other metal structures. H-section steel is an economic section steel with better mechanical properties than I-section steel. It is named because its section shape is the same as the English letter 'H'. The flange of hot rolled H-beam is wider than that of I-beam, with large lateral stiffness and strong bending resistance. Under the same specification, H-beam is lighter than I-beam.Alloy pipe is a kind of seamless steel pipe. Alloy pipe is divided into structural seamless pipe and high-pressure heat-resistant alloy pipe. It is mainly different from the production standard and industry of alloy pipe. Annealing and tempering of alloy pipe changes its mechanical properties. Meet the required processing conditions. Its performance is higher than that of ordinary seamless steel pipe, its utilization value is higher, the chemical composition of alloy pipe contains more Cr, and its performance of high temperature resistance, low temperature resistance and corrosion resistance. Ordinary carbon seamless tubes do not contain alloy components or have few alloy components. Alloy tubes are widely used in petroleum, aerospace, chemical industry, dead end welding of strip steel and circumferential seam. For the spiral welding of steel for the transportation of flammable general liquids boiler and other industries because the mechanical properties of alloy tubes change and are easy to adjust.

X-ray or ultrasonic testing shall be carried out for repair welding of alloy pipe,LarissaWelded pipe wholesale manufacturer, yibai%sx ray or ultrasonic testing shall be carried out. For the spiral welding of alloy pipes for the transportation of water, wastewater, heating steam and other general liquids, X-ray or ultrasonic testing sampling inspection (%) shall be carried out.consumption→ compared with the concrete structure, the I-steel structure can increase the service area by %, reduce the self weight of the structure by % - %, and reduce the structural design internal force. The cold-rolled stainless steel pipe has the advantages of large yield coefficient, no expansion, bending and so on. In order to reach the health grade standard of stainless steel pipeline, the pipeline after cold rolling must undergo bright annealing, demagnetization pickling, calibration and other procedures.Aiming at the connective tissue and texture produced in stainless steel plate Position and other crystal defects are generally removed by heat treatment processes such as quenching or quenching. The effect of quenching is to optimize the crystal, eliminate structural defects, reduce strength, improve plastic deformation, and also conducive to cold drawing. In the production and manufacture of cold drawn alloy pipe, quenching machinery and equipment cannot be lacked. Therefore, the formulation of appropriate annealing process is a necessary condition to ensure that the alloy pipe mechanism meets the standard and the commodity does not crack. If the manufacturer in order to better one sidedness, reduce the product cost and reduce the quenching process, it will eventually lead to bad harm to the product quality.Larissa,What should we pay attention to in the production of alloy pipeI-beam is divided into ordinary I-beam and light I-beam. The specification of hot rolled ordinary I-beam is -#. The specification of hot-rolled flexible I-beam supplied through agreement between the supplier and the buyer is -#. I-beam is mainly used in building structure vehicle manufacturing,LarissaHow much is I-beam per square meter, other industrial structures and fixed panels and cabinets. I-beam is often used together with I-beam.Under the action of thermal stress, because the initial temperature of the surface layer is lower than that of the heart and the shrinkage is greater than that of the heart, the heart is pulled. At the end of cooling, because the final cooling volume shrinkage of the heart cannot be carried out freely, the surface layer is compressed and the heart is pulled. That is, under the action of thermal stress, the surface of the workpiece is finally compressed and the center is pulled. This phenomenon is affected by factors such as cooling rate, material composition and heat treatment process. The faster the cooling rate, the higher the carbon content and alloy composition, the greater the uneven plastic deformation caused by thermal stress during cooling, and the greater the final residual stress. On the other hand, i.e. the transformation from austenite to martensite, the increase of specific volume will be accompanied by the expansion of workpiece volume, and each part of workpiece will undergo phase transformation successively, resulting in inconsistent volume growth and structural stress. The final result of the change of tissue stress is the tensile stress on the surface and the compressive stress in the center, which is just opposite to the thermal stress. The microstructure stress is related to the cooling rate, shape and chemical composition of the workpiece in the martensitic transformation zone.