Sign in perhaps register 。

Because all parts of I-beam are arranged at right angles,Elinique ó n Airport1Cr5Mo high pressure alloy pipe, I-beam has the advantages of strong bending resistance, simple construction, cost saving and light structural weight in all directions, and has been widely used. The inner and outer sides of the flange of the I-beam are parallel or close to parallel, and the end of the flange is at a right angle, so it is named parallel flange I-beam. The web thickness of I-beam is smaller than that of ordinary I-beam with the same height of web, and the flange width is larger than that of ordinary I-beam with the same height of web, so it is also named wide edge I-beam.Application characteristics of I-beam:Elinique ó n Airport,The advantage of the reinforcement mesh system is ecological. It is filled with natural stone materials. There is a gap between the stone materials to allow plants to grow in it. It can also plant plants on it. It has the dual effects of engineering slope protection and plant slope protection. The Ecological Grid mat is a combination with a height of cm ~ cm, mostly a multi grid box separated by spacer mesh.The general alloy pipe with improved performance is variable and has high application value. The alloy pipe contains more Cr and is heat resistant Low temperature resistance Corrosion resistance. There is no aluminum alloy in plain carbon seamless steel pipe, not very little aluminum alloy, and the alloy pipe is used in crude oil Aerospace Chemical plant Power engineering heating furnace. Because the physical properties of alloy tubes are easy to change and adjust.Delchevo The small length of repair welding is mm; The raw material shall not exceed mm after grinding by welding edge.H-section steelMixed Scabs are distributed periodically, we have produced galvanized pipe products for many years. Welcome friends who need to buy.I-beam can only be used for beam, while H-beam can be used for load-bearing column of structure.Design brand,I-beam, whether ordinary or light, can only be directly used for bending members or lattice members on its Web because of its large and narrow section size and large moment of inertia difference between the two main axes on the section. It is not suitable for axial compression members and flexural members perpendicular to the web plane, dead end welding of strip steel and circumferential seam. For the spiral welding of steel for the transportation of flammable general liquids, yibai%sx ray or ultrasonic testing shall be carried out. For the spiral welding of alloy pipes for the transportation of water, wastewater, gas, heating steam and other general liquids, X-ray or ultrasonic testing sampling inspection (%) shall be carried out.Main uses: as a finished material, flat steel can be used to make hoop iron, tools and mechanical parts, and used as building frame structural parts and escalators in buildings. Flat steel is divided into two types according to its shape: plane spring flat steel and single-sided double groove spring flat steel. Hot rolled spring flat steel is mainly used to manufacture leaf springs for automobiles tractors, railway transportation and other machinery.

H-section steel is an economic section high-efficiency profile with more optimized section area distribution and more reasonable strength weight ratio. It is named because its section is the same as the English letter 'H'. There is no slope on the inner side of the two outer edges of H-section steel, better mechanical properties per unit weight and can save a lot of materials and construction time.Quality assurance,Application characteristics of I-beamThe surface of cold galvanized layer is smooth, dense and uniform. It has good mechanical properties and corrosion resistance. The consumption of hot-dip galvanized coating is between % - %. The galvanizing process is complex, but the thickness of single-sided coating,Elinique ó n Airport15CrMo thick wall alloy pipe, surface coating and double-sided coating is different, so the thin-walled pipe shall be galvanized. The zinc coating has strong protection and corrosion resistance.Alloy tube is widely used in our daily life, which provides us with great assistance.Elinique ó n Airport,Patented manufacturing process of I-beam: I-beam has become a new industrial standard for wear-resistant materialsI-beam has the dual properties of high hardness and toughness materials. Compared with other engineering wear-resistant materials in China, such as various alloy steel plates, cast wear-resistant plates, cast stones, rubber, polyurethane, etc., it has irreplaceable comprehensive excellent properties. Judged as failing.