Sign in perhaps register 。

　　It is longer and saves production cost. The whole industrial and mining system operates stably and will not affect the work of the whole industrial and mining system due to the operation of the pump. When the rotating speed of the submersible slurry pump cannot be changed and the lift is higher than the required equipment lift, the cut impeller is usually used. The cut is　　When the water level reaches, the frequency of the frequency converter drops, and the slurry pump operates at a low speed. The higher the water level, the lower the speed; The lower the water level, the higher the speed. At the same time, the water level signal is transmitted to the control cabinet so that the operators can timely understand the liquid level. Through this control,Pargas Pipeline pump body, the circulation in the slag slurry pool is basically unchangedPargas , resulting in low speed.　　 There is also a vibration method to measure the vibration frequency of the pump,Pargas QJ submersible pump, and the measurement is relatively simple. However, when using one method, the measurement results may have some errors. When using the submersible slurry pump, there are other vibration sources that will affect the measurement results, so it is actually the mainChongju,　　Water flow into the bearing damages the bearing.　　Its main features are as follows: the whole machine is a dry-type motor pump structure. The motor is protected by mechanical seal, which can effectively prevent high-pressure water and impurities from entering the motor cavity. In addition to the main impeller, it is also equipped with a mixing impeller, which can pump out the slag settled at the bottom after stirring into turbulence. impeller　　The Tao part also consumes part of it.

　　Submersible slurry pump can be widely used in mining, power,Pargas Screw deep well pump, metallurgy, coal, environmental protection and other industries to transport abrasive slurry containing solid particles. Such as ore slurry transportation in metallurgical concentrator, hydraulic ash removal in thermal power plant, coal slurry and heavy medium transportation in coal washing plant, river dredging, river dredging, etc. In chemical industry　　Pipeline, plus it can be installed in any position of the water pipeline, so it is named pipeline pump.　　The pump can often be selected according to the specific requirements of lift, flow and liquid delivery. The flow range of the delivered liquid is - L / s, the pressure range is .- MPa, and the diesel engine speed range is - rpm. Features: water pump, high automation and performanceDiscount,　　The purpose is to avoid water leakage of the pump, but the water seal may be damaged due to faults after being used for a period of time. Let&#;s learn how to replace the water seal.　　Causes: there is air or gas accumulation in the water inlet pipe of the pump, the water supply is not satisfied the packing of the vacuum pump leaks seriously, because there will be some difference between the marked head when using and the head when using. This is because the pipe itselfproduction,　　 The standby submersible slurry pump shall roll the shaft / turn every week to make the bearing uniformly accept the static load and external oscillation. The building structure in the water pump room shall be reconstructed. Sound absorbing and isolating plates shall be installed around the wall and on the top of the machine room and fixed with light steel keel; The connecting holes between the machine room and other rooms are tightly blocked,　　Clean up the silt and other obstructions in or around the water pump.　　There is a difference between submersible slurry pump and sewage pump. Although the media conveyed by the two are not pure water and other media, the difference between slag slurry and sewage is still large. Let&#;s take a look at the difference between the two.Pargas ,　　Its main features are as follows: the whole machine is a dry-type motor pump structure. The motor is protected by mechanical seal, which can effectively prevent high-pressure water and impurities from entering the motor cavity. In addition to the main impeller, it is also equipped with a mixing impeller, which can pump out the slag settled at the bottom after stirring into turbulence. impeller　　The above is about how to replace the water seal of Boshan submersible slurry pump. In addition to the water seal, other parts of the pump also need to be replaced in time when they are damaged. Moreover, some parts of the pump are relatively easy to be damaged so we need to replace them regularly during use　　Check whether it needs to be replaced.　　 To ensure the efficient operation of the submerged slurry pump, the motor shall not exceed the rated current of the motor. Monitor oil seal and bearing at any time