Sign in perhaps register 。

I-beam: national standard * what is the wall thickness of I-beamI-beam is an economic section high-efficiency profile with more optimized section area distribution and more reasonable strength weight ratio. It is named because its section is the same as the English letter 'H'.Griff á Da,Third, between the flange on the inner side of the sidewalk beam and the old bridge deck, the widening part of the bridge deck is poured with concrete, and the concrete of the bridge deck pavement is poured at the same time to form a carriageway. The reinforcement mesh is set on the bridge deck pavement and the widening part of the bridge deck to strengthen the overall performance. Fourth, the bridge deck expansion joint is set at the center of the cantilever beam top, and the carriageway pavement is extended and erected on the cantilever beam.GB No. I-beam is in height, in leg width and in waist thickness.El-Coco,Determined by the shape, the section modulus, it shows its superior performance in bearing bending moment, pressure load and eccentric load. Compared with ordinary I-beam, it can greatly improve the bearing capacity and save metal by % ~ %.When we carry out different projects, we must use different raw materials, which can ensure the quality of the project. In many kinds of data, alloy pipe is widely used. In many projects, we will apply it, so it is very popular in the field. When people carry out the construction of alloy pipe project, there are many things that must be paid special attention to. Let&#;s take you to know:Its heat sealing effect is remarkable. It can be directly buried immediately, which can not only save resources,Griff á DaCustom welded pipe, but also reduce consumption, not occupy the natural environment, but also purify the environment. The transportation of gas can meet the requirements of long-distance transportation, prevent actual operation and maintenance, meet the requirements of thermal insulation and cold protection, reduce heating equipment, unique and convenient installation, and reduce the construction cycle time of the project. On the whole, it is more convenient to use. It can also be used for the transportation of floor heating and hot springs.

Classification introductionSpeed up the construction progress: weld the mesh with reinforcement to allow the rapid construction of the project. The required laying of welded steel bars is provided, so concrete can be poured, steel cutting, stitching, etc. and the arrangement can be strengthened. ？ saving construction time? The construction progress is greatly accelerated and the construction period is shortened.I-beam features: the content of chromium carbon alloy is -%, the hardness of chromium carbide alloy is V,Griff á DaWhat is the inner diameter and outer diameter of the welded pipe,Precision cold rolling of small and medium-sized bearing sleeves with alloy tubes can greatly improve material utilization, bearing performance and service life. This paper systematically introduces the service life of high quality cold drawn bearings.Alloy pipe can be divided into round steel pipe and special-shaped steel according to different cross-sectional area. Because the circular area is large on the premise of the same side length, a large amount of liquid can be transported with an annular tube. In addition, when the circular cross section bears the internal or external axial working pressure, the bearing force is more symmetrical. Therefore, most seamless steel pipes are round steel pipes.All the cracks occur at -mm away from the edge below the alloy pipe, and the macroeconomic orientation is vertical to the cold rolling orientation, showing a 'high mountain' shape.

The defects can be removed by grinding with sand wheel, but the remaining wall thickness must be within the allowable standard.How much does it cost?,The specification of I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is cm. The types of I-beam include hot-rolled ordinary I-beam Light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~ mm, expressed as No. ~ No., and the inclination of inner side wall of leg is : The pass system of rolled I-beam includes direct rolling pass system, cross rolling pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.Transformer tube: it is used to make transformer heat dissipation tube and other heat exchangers. It is made of general carbon steel. Flattening flaring, and there are certain requirements for the tortuosity of steel pipes.Classification introductionGriff á Da zigzag and hydraulic tests are required. Steel pipes are delivered in fixed length or double lengthSo why is the alloy pipe easy to rust after being pickled and passivated by the software?Generally, the process of pickling and passivation will be carried out for alloy pipes, but the alloy pipes after pickling and passivation are very easy to rust. Therefore, the way to find a solution to wiredrawing corrosion is 'grinding and polishing'. Due to grinding and polishing, there is no harm to carry out hot galvanizing in the middle and later stage.C-section steel has uniform zinc layer, strong adhesion, no zinc scar, no zinc leakage and high dimensional accuracy. All surfaces are wrapped by zinc layer, and the zinc content on the surface is usually -g /? It has long service life, corrosion resistance and durability. It is a kind of stronger protection.