Sign in perhaps register 。

Whether I-section steel is ordinary or light, due to the relatively high and narrow section size, there is a large difference in the moment of inertia between the two main sleeves of the section. Therefore it can only be directly used for members bent in the plane of their web or form lattice stress members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application.→ under the same section load, the weight of hot-rolled H steel structure is reduced by % - % compared with the traditional structure.Wallos,There are many types of galvanized pipes, mainly including cold plated seamless pipes and hot-plated seamless pipes. But now the previous one is no longer used. The hot-dip seamless tube is still in use. Hot dip galvanized pipe is mainly used for steel pipes with low pressure fluid such as water and gas. When in use, if in normal working environment, the thickness of galvanized layer of hot-dip galvanized seamless steel pipe is up to μ M above, and it has been used safely for about years. It can be seen that its service life is very long. Of course, when purchasing, we should also find regular manufacturers to order. Only in this way can we achieve this service life. As long as the galvanized pipe is cleaned after pickling, it is basically cleaned in ammonium chloride or zinc chloride aqueous solution or ammonium chloride and zinc chloride mixed aqueous solution tank. In order to ensure the quality, although it is much cheaper in price. However, the quality is very good when used, and it is also easy to have problems. The small length of repair welding is mm; The raw material shall not exceed mm after grinding by welding edge.Rengasdengklok, Hot stamping. Fix the plan product workpiece or preformed vacancy on the rotating journal, with the wheel working pressure vacancy, radial wheel. After one or several solutions, specification scope, mold shell and software requirements, which are very simple, very easy to be replaced,WallosIs the steel bar cold rolled or hot rolled, and relatively low product cost. The processing time is not long enough, the processing capacity is not high, the total length of processing pipeline is limited, and the size of machinery and equipment is generally short.Alloy pipe is a very important way and type of seamless steel pipe. Its use is relatively common. It is widely used in various engineering projects, house construction and building decoration. Its fracture will always be found in the production, manufacturing and key marketing of alloy pipe, That is, many stages of production and processing are not done well. Another is that the seasoning is not enough and the proportion of chemical molecules is wrong. There are all reasons.I-beam is mainly divided into ordinary I-beam, light I-beam and wide flange I-beam. According to the height ratio of flange to web, medium and narrow flange I-beams. The specifications of the first two are -, that is the corresponding height is -. At the same height, the light I-beam has narrow flange, thin web and light weight. Wide flange I-beam, also known as H-beam, so it is also called 'universal I-beam'. Ordinary I-beam and light I-beam have formed national standards.

After the passivation treatment of alloy pipe,Wallos4. How much is a ton of sub welded pipe, it is clearly proposed that water cleaning shall be carried out immediately after the aqueous solution, ~ times of water cleaning, and then chromic acid closed solution shall be carried out. Chromic acid solution must be carried out h after the subsequent water cleaning of metallographic structure and austenitic alloy pipe. Chromic acid aqueous solution (mass ratio) is % ~ %, the solution temperature is ~ ℃, and the solution time is min. Then dry.The advantage of the reinforcement mesh system is ecological. It is filled with natural stone materials. There is a gap between the stone materials to allow plants to grow in it. It can also plant plants on it. It has the dual effects of engineering slope protection and plant slope protection. The Ecological Grid mat is a combination with a height of cm ~ cm, mostly a multi grid box separated by spacer mesh.Advantages of using I-beam: reduce maintenance cost reduce downtime, improve equipment operation rate, reduce wear, reduce equipment capacity and increase power consumptionMeticulous workmanship,I-beam is a long strip steel with groove section, which belongs to carbon structural steel for construction and machinery. It is a section steel with complex section, and its section shape is groove shape. China&#;s imports of I-beams are greater than its exports. The main producing areas are Tangshan Iron and steel, Baotou Iron and steel, Shangang, huangte, Maanshan Iron and steel, Xuanhua Iron and steel, Japan iron and steel, etc.→ compared with general section steel, it has the advantages of low cost, high precision and small residual stress. It does not need expensive welding materials and weld detection, and saves about % of the manufacturing cost of steel structure.Its heat sealing effect is remarkable. It can be directly buried immediately, which can not only save resources, but also reduce consumption, not occupy the natural environment, but also purify the environment. The transportation of gas can meet the requirements of long-distance transportation, prevent actual operation and maintenance, meet the requirements of thermal insulation and cold protection reduce heating equipment, unique and convenient installation, and reduce the construction cycle time of the project. On the whole, it is more convenient to use. It can also be used for the transportation of floor heating and hot springs.

C - section steel is reliable and stable in stress, can be accurately positioned, and is resistant to impact and vibration Moreover, and has a variety of C-section steel and size selection to ensure its flexibilityService first,Alloy pipes can be used for heating (cooling) projects.Installing the pipe structure means the complexity of some elements.What should we pay attention to in the production of alloy pipeWallos,What are the requirements for alloy pipe construction accessoriesBecause alloy pipe is a very unique pipe fitting, we must use appropriate methods to carry out installation in the case of installation, so as to ensure the performance index of the data. Generally, when installing alloy pipes, we will use some flanges and elbows to fix them, so as to ensure that the raw materials can be fixed very well. Therefore, when we carry out use, we must ensure the quality of flanges and elbows, so as to ensure the actual effect of alloy pipe assembly. If there are instrument panel components that must be assembled on the pipeline they must be installed together.Ways to obtain surface compressive stress characteristics of alloy tubes