Sign in perhaps register 。

　　 The fixing method of the impeller is changed from screw thread to key clamp to prevent the impeller from falling off and causing damage!　　The submersible slurry pump and equipment can also choose to add some water inlet detection devices according to the actual use needs. The overheat monitoring devices are often used in a large amount in time, and the pump and motor of the equipment used in time are the same shaft, soSaint Nicholas,　　 The motor output of the large flow submersible pump is too high, there are other electric equipment on the user&#;s site, and the user&#;s Transformer composition capacity is too small to start the submersible pump. You can use a suitable transformer or turn off other electrical equipment that meets the power consumption of the submersible pump.　　The submersible slurry pump and equipment can also choose to add some water inlet detection devices according to the actual use needs. The overheat monitoring devices are often used in a large amount in time, and the pump and motor of the equipment used in time are the same shaft, soLeshno,　　The premise of using this method is that the water gun must have sufficient flow during use, otherwise the effect of the submersible slurry pump may not be obvious.　　There is a difference between submersible slurry pump and sewage pump. Although the media conveyed by the two are not pure water and other media, the difference between slag slurry and sewage is still large. Let&#;s take a look at the difference between the two.　　After understanding the working principle of the submersible slurry pump, we will also know that those parts are prone to wear during normal use. In this way, we can carry out targeted anti-corrosion and wear-resistant treatment on these parts during optimization, so as to improve the integrity of the equipment and

　　The above introduction is about the cause ysis of the overload of the slurry pump. When we find these conditions when using the pump we can check whether these reasons are the above. This is also a reminder that we need to maintain the pump during normal use. latent　　In this way, pull the pull nut, take out the gasket, tighten the pull nut evenly,Saint NicholasUsed pipeline pump, and then rotate the electric pump from the coupling. The rotation must be uniform.　　 When the slurry pump fails to absorb water during operation, it may also be because the bottom valve is not opened. At this time,Saint NicholasSelf priming slurry pump wholesale, it is necessary to check whether the bottom valve is open and make corresponding adjustment.average method, so it has an irreplaceable position when it is used. What is its own structure when it is used.　　The supply of shaft seal water must be ensured. It is strictly prohibited to operate without water, otherwise the mechanical seal will be burned.　　A large amount of lubricating oil is stored.

　　Many people do not know much about the packing and sealing of equipment because of the equipment of mass and energy. Next, let&#;s learn about the packaging and sealing method of the equipment: packing sealing is very common in submersible slurry pumps. This method has good sealing performance, is easy to use, and effectively reduces the wear of the host and anti vibration kinetic energyreform,　　There are many types of submersible slurry pumps available in the market, and different pump models have different performance and application fields. Therefore, although the pump has a wide range of applications if its model is not correctly and reasonably selected, its application effect will be great　　For the pipeline pump in the workshop, check the motor during installation but the performance of the pipeline pump is degraded. In case of abnormal water absorption during installation, and check the motor wiring and speed,　　For example, concentrate and tailings are treated in the concentrator, ash and slag are removed from the power plant, slime and dense medium coal are transported in the coal preparation plant, and slurry is transported in coastal river mining operations. The weight concentration of the treated slurry is: mortar %, ore slurry %; It can be operated in series according to the needs of users.Saint Nicholas,　　It should be /-/ between. When the packing is worn, the packing gland can be properly pressed. If it is worn too much, it should be replaced. The whole commissioning process of the submersible slurry pump mainly includes the above five tasks,Saint NicholasSubmersible pump can pump sewage, which are mainly to pay attention to the details and the phenomena occurred during the operation, and timely deal with the problems in time to avoid being on duty Accidents during operation cause losses.　　How to avoid this situation when the equipment is in use.　　 The rotor assembly is designed according to the actual situation, and the operation is more stable!