Sign in perhaps register 。

Zinc layer thickness: there is a great difference between cold galvanized square pipe and hot galvanized square pipe in galvanizing process; Cold galvanized square pipes are prone to & ldquo; Electric burning & rdquo; The color of this part is gray and the zinc layer is thick. It is easy to form a current dead angle at the corner,HorolaHow much is a ton of galvanized square tube, resulting in an under current area. The zinc layer at this part is thin and there is no zinc layer attached to the cold galvanized square pipe. The cold galvanized square pipe has no zinc lump and caking as a whole, but the overall zinc layer is thin, and the thickness of the outer wall zinc layer is μ m-μ m. The and outer walls of the hot-dip galvanized square tube are attached with zinc layer, and there will be water marks and a few zinc tumors, but the overall zinc layer is thick, plasticity and hardness discussed above in fatigue QB are the indicators of the mechanical properties of metals under static load. In fact, many machine parts work under cyclic load, under which fatigue will occur.Horola,After aluminum deoxidation in molten steel, & omega; When (ALS) is .% ~ .%, calcium treatment can achieve better effect on the denaturation of Al.Principle of cold drawing strengthening: the lattice defects of steel increase during plastic deformation, and the serious distortion of defect lattice will hinder the progress and slip of lattice, so the yield point of steel increases and the plasticity and toughness decrease. Due to the internal stress in plastic deformation, the modulus of steel decreases. The cold drawn reinforcement is stored at room temperature for ~ d or heated to ~ ℃ and maintained for a fixed time. This process is called aging treatment.Phrae,For oil, the oil brush work shall be carried out in accordance with the requirements of the rule system,Horola25mm galvanized square pipe, so as to ensure the oil brush and the oil in the correct position of the brush and avoid wrinkles.Among them, qb square tube is divided into: (a) by process & mdash& mdash; Arc welded square pipe, resistance welded square pipe (high frequency and low frequency), gas welded square pipe and furnace welded square pipe (b) are divided by weld & mdash& mdash; Straight seam welded square pipe, spiral weldingMechanical engineering, power plants, agricultural and chemical machinery, glass curtain walls automobile chassis, airports, boiler construction, highway railings, housing construction, pressure vessels, oil storage tanks, bridges, power station equipment, heavy transportation machinery and other welded structural parts with high load, etc. Process classification: according to the production process, square tubes are divided into hot-rolled seamless square tubes, cold drawn seamless square tubes seamless square tubes and qb square tubes.

The first is to remove the rust of the square tube. When removing the rust of the square tube, the steel wire brush is mainly used to polish its surface, which can effectively remove the loose or rusty rust on the surface of the square tube.× × ～ × × ～ × × ～ × × ～ × × ～ × × ～ × × ～ × × ～ × × ～ × × ～ × × ～ × × ～ × × Standard treatment of steps for preventing oxidation of ~ square tube square tube is a kind of metallic maintenance. The main components are iron and zinc. It is easy to have redox reaction in the air. Once the reaction occurs, many new substances have taken place, and the original characteristics have changed. However, in order to maintain the original relevant characteristics, anti-oxidation treatment is required. The direct reason is to prevent the square tube from reacting with the oxygen in the air, which is the way to isolate the oxygen in the air. Today, this article makes a relatively standardized treatment on the relevant steps to prevent oxidation of square tubes: the key depends on what kind of antirust paint you use. . If you use epoxy zinc rich or iron rich antirust paint,HorolaGalvanized square tube merchant, you can directly spray fluorocarbon paint on it; if alkyd antirust or red lead is used, it shall be cleaned with paint remover and sprayed with epoxy zinc rich or iron rich antirust paint again before fluorocarbon paint can be sprayed.The disadvantage of solid bending is that it has tensile thinning effect. The actual bending will produce tension at the bending point,The principle of straightening machine is that a disc is divided into two sides to clamp round steel straight lines. Professional square tube, square rectangular tube, seamless square tube, galvanized square tube, galvanized tube, high price, service, on-site settlement, honest operation! The edge is one with radius r, and the other outer edge must be two equal diameters with radius R. The diameter of the reinforcement to be straightened is D, and the center distance between them is adjusted to R + R + D.In this period, the technology of continuous rolling pipe was not mature.Ship carbon steel square pipe (gb-) is a carbon steel square pipe for ship class I pressure pipe system, class II pressure pipe system, seamless square pipe square pipe, galvanized square pipe and galvanized pipe. Welcome to consult. The working temperature of carbon steel square pipe wall shall not exceed ℃, and the working temperature of alloy steel square pipe wall shall exceed ℃.

Structural stainless steel square pipe (gbt-) is a hot-rolled (extruded, expanded) and cold drawn (rolled) square pipe made of stainless steel for corrosion-resistant pipes, structural parts and parts widely used in chemical, petroleum, light textile, machinery and other industries.Test conclusion,Carbon steel classified by chemical composition: square tube A. low carbon steel (C & le; .%); b. Medium carbon steel (C & le; . ~ .%); c. High carbon steel (C & le; .%).Surface adhesion resistance is an important feature of square tubes. At present, square tubes are mostly used for transportation, so the adhesion resistance makes square tubes not stick during transportation.The reason why it is divided into two types is that chemical cleaning can only clean the surface very thoroughly, and it is difficult to achieve the desired results in some fine cracks.Horola,Principle of cold drawing strengthening: the lattice defects of steel increase during plastic deformation, and the serious distortion of defect lattice will hinder the progress and slip of lattice so the yield point of steel increases and the plasticity and toughness decrease. Due to the internal stress in plastic deformation, the modulus of steel decreases. The cold drawn reinforcement is stored at room temperature for ~ d or heated to ~ ℃ and maintained for a fixed time. This process is called aging treatment.The pipeline is only subject to chemical pickling, which can remove oxide scale, rust and old coating. Sometimes it can be used as the reprocessing after sand blasting. Although chemical cleaning can make the surface reach a certain cleanliness and roughness, its anchor lines are shallow and easy to pollute the surrounding environment. The square tube shall be submitted for acceptance in batches, and the batch rules shall comply with the provisions of corresponding product standards.: it refers to the processing of square tube, which places metal in a closed Jane and applies pressure at the end to extrude the metal from the specified die hole to obtain finished products with the same shape and size. It is mostly used to produce non-ferrous metal materials. Square tube ferrous metal, steel and non-ferrous metal. Before introducing the classification of steel, briefly introduce the basic concepts of ferrous metal