Sign in perhaps register 。

Low power consumption: When the hydraulic guide rail lifting platform descends, it is driven by the pressure generated by its own weight, greatly saving energy and reducing consumption.Safety grounding device. In order to protect against electrical equipment. The metal casing of electrical equipment and the metal structure of electric elevators should be equipped with a safety grounding device. The grounding wire should operate multiple wires, and the neutral wire should not be arbitrarily held as a safety grounding wire. Its grounding resistance should not exceed ohms; The power supply of the electric elevator can be cut off.Ramsey,Aluminum alloy lifting platforms can be divided into single column aluminum alloy,RamseyElectric mobile elevator, cargo elevator, three column and four column aluminum alloy. Can be used in factories, automated warehouses, parking lots,RamseySelf propelled electric elevator, municipal facilities, docks, buildings, smooth lifting and low noise.Agadez,It is reported that a fixed electric elevator has good lifting stability and can only be used for fixed operations, floors, or other lower suspended structures, the bearing capacity of the foundation support structure should be checked. Click here to download the construction technical information for free. Basic drainage facilities should be installed.Setting requirements: The anti loosening and anti loosening parts between the connecting parts should comply with the provisions of the user manual and should not be replaced by other objects. For connecting bolts with pre tightening requirements, a torque wrench or special tool should be used to accurately tighten the bolts to the specified torque value according to the specified tightening sequence. When installing standard section connecting bolts, it is advisable to place the screw at the bottom and the nut at the top.

Buffer. In order to increase the energy for the car to hit the top or sink to the bottom. Remove rubber or sponge from the buffer and cabin to increase their impact energy; Rope groove slipping and other accidents caused the car to suddenly fall, resulting in a safety clamp. To prevent breakage of the lifting wire rope. A safety clamp that can simultaneously cut off the power supply and stop the car from falling should be removed from the car. A car without safety tongs is not allowed to ride or carry people. If it is a simple electric elevator there should be a safety device (such as a safety stop pin) to prevent people from suddenly falling when loading and unloading goods in the car; Electric elevators with three or more floors (including three floors) for passengers or passengers.When using lifting equipment, the workbench should be kept in a horizontal state.The spacing between wall brackets and the height of guide rails above the high attachment point should comply with the requirements of the user manual.Where is good,The landing door should be in a normally closed state. Without the permission of the construction electric elevator driver, the landing door shall not be opened.Speed limit wire rope switch. When the speed limit wire rope trips or breaks. Make the electric elevator unable to start.During normal operation, the horizontal distance between the closed cage door and the closed landing door should not exceed mm. Otherwise, measures should be taken to make it meet the requirements, or side protection devices at the entrance of the landing station that meet the requirements should be equipped. The distance between any opening between the side protection device and the hanging cage or landing door should not exceed mm.

Electric elevators used in various places.Free consultation,The entrance of each landing platform must be equipped with a landing door, which must open towards the landing platform side, and the door bolt must be set on the side next to the construction electric elevator.Is the water cooling and air cooling of the hydraulic station the same?During normal operation, the horizontal distance between the closed cage door and the closed landing door should not exceed mm. Otherwise, measures should be taken to make it meet the requirements, or side protection devices at the entrance of the landing station that meet the requirements should be equipped. The distance between any opening between the side protection device and the hanging cage or landing door should not exceed mm.Ramsey,RamseyFolding electric elevator,Low level doors should be equipped with interlocking devices that can verify their closed and locked positions. The action of this interlocking device should be at the entrance of the cage. Simple use should not interfere with the operation of the interlocking device. The attached wall bracket should use matching standard products. When the wall bracket cannot meet the requirements of the construction site, it should be designed separately. The design of the wall bracket should meet the requirements of component stiffness, strength, stability etc., it is driven by the pressure generated by its own weight and the production should meet the design requirements.Setting requirements: The spacing of wall brackets along the vertical direction should comply with the provisions of the user manual.Low power consumption: When the hydraulic guide rail lifting platform descends, greatly saving energy and reducing consumption.