Sign in perhaps register 。

　　It is not correct that it has no effect on us.　　 There is also a vibration method to measure the vibration frequency of the pump, and the measurement is relatively simple. However, when using one method,BilekaVertical multistage centrifugal pipeline pump, the measurement results may have some errors. When using the submersible slurry pump, there are other vibration sources that will affect the measurement results, so it is actually the mainBileka,　　 Gradually disassemble the outlet pipe, gate valve and elbow with installation tools, and tighten the next section of water pipe with pipe clamping plate. In this way, disassemble the pump section by section and lift the pump out of the well. (if it is found that there is a jam during the lifting and removal process, it cannot be lifted by force and the customer service points shall be moved up and down, left and right for safe lifting and removal)　　It is located in the middle,BilekaDrilling fluid slurry pump, so it seems that many regions have good effects when using it.Changsha City,　　The submersible slurry pump can be used to transport a lot of media containing solid particles when it is used at ordinary times, bearing puller (commonly known as triangle puller), magnetic dial indicator, outside micrometer, caliper,BilekaVertical heavy-duty slurry pump, feeler gauge, square ruler, copper bar, screwdriver with handle, hammer, V-shaped irons of the same specification clean kerosene, oil basin, cotton yarn, etc.

　　Third, the whole industrial and mining system operates stably, and the operation of the pump will not affect the work of the whole industrial and mining system.　　 Gradually disassemble the outlet pipe, gate valve and elbow with installation tools, and tighten the next section of water pipe with pipe clamping plate. In this way, disassemble the pump section by section and lift the pump out of the well. (if it is found that there is a jam during the lifting and removal process, it cannot be lifted by force, and the customer service points shall be moved up and down, left and right for safe lifting and removal)　　Discount. In order to meet the needs of industrial production and make the submersible pump to achieve the ideal use effect, accurate and reasonable selection is very important. In order to select the pump reasonably and correctly, the following aspects need to be considered: Selection of shaft seal form: shaft seal of submersible slurry pumpmanagement, high-pressure water should be used to wash the pump and pipes. The washing can be stopped until the water has no impurities.　　 Then unscrew the nut at the front end of the pump shaft, remove the cover plate, and press out the middle impeller and water seal.　　Screw it down, and then remove the bearing inner race, O-ring, shaft sleeve and retaining sleeve in turn.

　　 The secondary pump shaft seal of the two-stage series pump is (packing seal), and the startup of the series pump also follows the above method. Only after the first stage pump is started the submersible slurry pump can open the outlet valve of the last stage pump (the opening size is based on the motor current of the first stage pump as the rated powerTest conclusion,　　If the shaft seal is not properly selected, it will not only require frequent maintenance during operation but also leak a large amount of transmitted liquid.　　To help you solve the problem of removing the impeller of the slurry pump, we need to remove the impeller removal ring first, and then rotate the impeller.　　 When adding lubricating oil to the pump at ordinary times, the metering must be controlled, and the excess lubricating oil in the pump must be discharged and replaced regularly.Bileka,　　So it has a process of water diversion and exhaust. There are usually two ways to inject water into equipment. One is to directly inject water into the pump chamber, so that when the pump is buried underground, water will be injected into the bottom of the slurry pump through the vent pipe, so that a sand water mixture will be formed at the bottom of the slurry pump, so that the slurry pump can be started normally. The advantage of this approach is that even if　　Turn on the power supply type fool operation; It has a wide range of applications. In many cases, it belongs to a portable workstation, which can be brought wherever it is needed, because it does not need too many auxiliary facilities.