Sign in perhaps register 。

Aachen4. How much is a ton of galvanized pipe,

Alloy pipe is a very important way and type of seamless steel pipe. Its use is relatively common. It is widely used in various engineering projects, house construction and building decoration. Its fracture will always be found in the production, manufacturing and key marketing of alloy pipe, That is, insulated and cooled in a certain medium, and their metal properties are controlled by changing the metallographic structure on the surface or inside of the material. During the heating and cooling process of structural welded steel pipe workpiece, due to the inconsistency of cooling speed and time between the surface and the core, the temperature difference will be formed which will lead to uneven volume expansion and contraction and produce stress, that is, thermal stress.Aachen,The production of plastic impregnated welded steel wire mesh is to immerse the formed welded steel wire mesh into a stone groove filled with PVC powder. The dry forming process is complex and the cost is much higher than that of spray welded mesh. Due to different application ranges and different uses, the choice is expensive or cheap, which needs to be determined according to its actual use.X-ray or ultrasonic testing shall be carried out for repair welding of alloy pipe, dead end welding of strip steel and circumferential seam. For the spiral welding of steel for the transportation of flammable general liquids, yibai%sx ray or ultrasonic testing shall be carried out. For the spiral welding of alloy pipes for the transportation of water, wastewater gas, heating steam and other general liquids, X-ray or ultrasonic testing sampling inspection (%) shall be carried out.Clarevo,When it is used for ground heating and hot spring transportation, it can meet the requirements of refrigeration and achieve the practical effect of less damage. It is applicable to water conservancy engineering, mining and other industries to meet the provisions of cold, cold and corrosion prevention. In addition, the chemical raw material transmission pipeline has a wide indoor space.What should we pay attention to in the production of alloy pipeWhether I-section steel is ordinary or light, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members.

According to the national standard of hot rolled H-section steel in China (GB / t-,Aachen27SiMn large diameter seamless pipe, H-section steel is divided into narrow flange, wide flange and steel pile, whose codes are Hz, while wide flange H-section steel and H-section steel piles are suitable for axial compression members or compression bending members. Compared with H-section steel, W, IX and iy are not as good as H-section steel under the premise of equal weight.External steel bonding reinforcement method is a more traditional reinforcement method. The utility model uses an adhesive to paste the steel plate or reinforcement mesh on the cracked part of the wall to achieve the purpose of reinforcement. The commonly used adhesive is usually epoxy resin. This method is simple and fast in construction and has little impact on production and life. Basically, the bearing capacity of the wall can be greatly improved without changing the shape and internal use space of the components. It is mainly applicable to the reinforcement of walls that do not allow to increase the section size of original components, but can greatly increase the section bearing capacity.Generally, the process of pickling and passivation will be carried out for alloy pipes, but the alloy pipes after pickling and passivation are very easy to rust. Therefore, the way to find a solution to wiredrawing corrosion is 'grinding and polishing'. Due to grinding and polishing, there is no harm to carry out hot galvanizing in the middle and later stage.Scheme customization, The defects can be removed by grinding with sand wheel, but the remaining wall thickness must be within the allowable standard.Aiming at the connective tissue and texture produced in stainless steel plate Position and other crystal defects are generally removed by heat treatment processes such as quenching or quenching. The effect of quenching is to optimize the crystal,AachenHow many inches of galvanized pipe 140?, eliminate structural defects, reduce strength, improve plastic deformation, and also conducive to cold drawing. In the production and manufacture of cold drawn alloy pipe, quenching machinery and equipment cannot be lacked. Therefore, reduce the product cost and reduce the quenching process, it will eventually lead to bad harm to the product quality.The high-temperature passivation treatment of alloy pipe is to obtain the passivation treatment film by heating in the heat treatment equipment. Before passivation treatment, the surface layer of parts must be removed to remove waste. At a higher temperature, the passivation treatment film can be obtained according to the transformation temperature and time. The hue of passivation treatment film can refer to the annealing color of alloy pipe, and the main parameters of ambient temperature and time of heat treatment process can be selected.

Plan scheme : Martensitic chromium alloy pipe and chromium alloy pipe with Cr composition exceeding %, without high carbon steel and high chromium alloy pipe. The aqueous solution contains % sodium cyanide % ~ % (volume ratio), the solution temperature is ~ ℃, and the solution time is min.Create brilliance, H-section steel is an economic section steel with better mechanical properties than I-section steel. It is named because its section shape is the same as the English letter 'H'. The flange of hot rolled H-beam is wider than that of I-beam, with large lateral stiffness and strong bending resistance. Under the same specification, H-beam is lighter than I-beam. Because the zinc coating has excellent ductility, bending and so on without damaging the coating.I-beamAachen rolling The defects can be removed by grinding with sand wheel, but the remaining wall thickness must be within the allowable standard.The shape of small longitudinal crack on the surface of alloy pipe is less than mm The overall width is less than mm The depth is lower than .mm. Small longitudinal crack