Sign in perhaps register 。

There are problems with the hydraulic torque converter and compensation system of mobile elevators, such as weak torque converter, power shift failure,KennethManufacturer of scissor lift, high oil temperature, inadequate pressure adjustment, insufficient back pressure. Check the quality of torque converter oil (whether hydraulic transmission oil is misused), dosage, torque converter pressure regulating valve, back pressure valve and their set pressure value. Power shift failure. Quick return valve, pressure reducing valve, power transmission valve The directional valve is stuck or leaking internally. Oil pollution is severe. Check the cause of the valve sticking and eliminate it accordingly. Filter or replace the hydraulic oil. If the oil temperature rises too much, check if there is any problem with the cooler. Check the quality of the hydraulic oil. The brand hydraulic boarding bridge, also known as the hydraulic loading and unloading platform, can achieve rapid loading and unloading of goods. The structure design is simple, the use is flexible and convenient, and the work efficiency is high. It is widely used and widely popularized in the market.Replace with new oil and do not intermittently use old oil, otherwise the moving parts in the system will accelerate wear.Kenneth,When the motor connection of the elevator is incorrect, when a coil coil group, or one phase winding group is connected in reverse, it can cause serious three-phase current imbalance and cause the winding to overheat.Firstly, it is necessary to use and operate the elevator correctly. The operators should receive systematic operation training: regular inspection of operating standards should be carried out, and any violations of elevator operation should be detectedCastelli,Mobile elevators are generally used in skyscrapers where electric elevators are used, as there is no need to stop midway, so fast elevators are needed. First go to the high-rise sky lobby (high-rise elevator lobby, Skylobby) from the ground, and then transfer to the ordinary elevator to the destination. Some new elevators use elevator pre calling systems, which can pre call designated floors in the lobby. These passenger elevators can be decorated beautifully according to customer needs. Some passenger elevators are also equipped with air conditioning and television, while others are set up in the cabin, so that customers can enjoy the scenery outside while riding.Drain all the hydraulic oil in the oil tank, open the oil tank, take out the oil suction filter, clean it, and return it to the oil tank. Install it in its original position. Fill the fuel tank with new oil.Mobile elevators are generally used in skyscrapers where electric elevators are used, as there is no need to stop midway, so fast elevators are needed. First go to the high-rise sky lobby (high-rise elevator lobby, and then transfer to the ordinary elevator to the destination. Some new elevators use elevator pre calling systems, which can pre call designated floors in the lobby. These passenger elevators can be decorated beautifully according to customer needs. Some passenger elevators are also equipped with air conditioning and television, while others are set up in the cabin, so that customers can enjoy the scenery outside while riding.

Novice operators: Due to their lack of understanding or lack of understanding of the operation methods of high-altitude work platforms such as mobile elevators, it is easy for them to make mistakes and cause equipment malfunctions. Operators in this area need to patiently learn and pass training before they can operate and use them.Attention should be paid to inspecting whether each steel wire rope has broken wires and loose strands. If it exceeds the relevant regulations, at low temperatures, the hydraulic oil used in summer can become,KennethMechanical hydraulic lifting platform, it is important to remember to replace hydraulic oil containing antifreeze, which is suitable for working at low temperatures.how much,What are the advantages of installing a guide rail type elevator for goods? The advantages of civil engineering are easy to install: there is no need for a machine room above the shaft and the top layer can be installed at a height of more than meters. The computer room can be located within a radius of meters of the shaft, occupying an area of only - square meters. The hydraulic elevator is not equipped with a counterweight device to improve the utilization rate of the shaft area. The load and load cylinder of the hydraulic elevator directly act on the foundation pit and the strength requirement for the shaft is low. A brick structure or brick concrete structure shaft is sufficient.When encountering overheating in the electric motor during daily maintenance of the elevator,KennethAluminum alloy hydraulic lifting platform, it is necessary to quickly park the car, remove obstacles, and then continue running. The motor bearings should be smooth and excellent.What are the installation precautions for elevators? The folding fence and cage of the elevator should be cleaned of the foundation surface, and the foundation bolts should be installed properly. If the construction elevator is installed on the floor, a pad iron must be used below the screws to increase the force surface between the nuts and the floor to reduce the impact of the nuts on the floor; Insert steel plate shims of different thicknesses between the chassis and the foundation stone at the anchor bolts to adjust the verticality of the guide rail frame; Install three standard sections and measure the verticality of the guide rail frame using a theodolite to ensure the verticality of each main pipe in both directions. After adjusting the verticality of the guide rail frame, tighten the four foundation bolts; Adjust the verticality of the fence door frame as above and tighten the remaining anchor bolts; Install the buffer spring; Connect the other half of the fence to the front half with bolts; Adjust the verticality and tighten the anchor bolts as above, and release the brake on the motor inside the suspension cage. (For SC/ models, first install the suspension cage before installing the drive plate).

Regular inspection and maintenance, eliminating hidden dangers, and troubleshooting are beneficial for improving work efficiency, extending equipment service life, and ensuring the safety performance of elevators.Where can I find it?There are problems with the hydraulic torque converter and compensation system of mobile elevators, such as weak torque converter, power shift failure, high oil temperature, insufficient hydraulic torque converter, inadequate pressure adjustment, insufficient back pressure. Check the quality of torque converter oil (whether hydraulic transmission oil is misused), dosage, torque converter pressure regulating valve, back pressure valve and their set pressure value. Power shift failure. Quick return valve, pressure reducing valve, power transmission valve The directional valve is stuck or leaking internally. Oil pollution is severe. Check the cause of the valve sticking and eliminate it accordingly. Filter or replace the hydraulic oil. If the oil temperature rises too much, check if there is any problem with the cooler. Check the quality of the hydraulic oil. The brand hydraulic boarding bridge, also known as the hydraulic loading and unloading platform, can achieve rapid loading and unloading of goods. The structure design is simple, the use is flexible and convenient, and the work efficiency is high. It is widely used and widely popularized in the market.The correct use of hydraulic elevators can extend their service life and also play an important role. So how should they be used?The hook of the seat belt should not be hung on unstable or moving objects. High priced and various specifications of scissor lift manufacturers provide timely supply, with high cost-effectiveness, and have become the preferred brand for many wire products. Welcome to purchase!Kenneth,Loosening: The newly processed and assembled components of high-altitude work platform equipment such as mobile elevators have a tendency to have geometric shapes and matching dimensions. In the early stages of equipment use, due to the influence of alternating loads such as impact and vibration, or factors such as heat and deformation, coupled with rapid wear and tear, as overloading can increase the burden on the motor and in severe cases, cause the motor to burn out.What are the advantages of installing a guide rail type elevator for goods? The advantages of civil engineering are easy to install: there is no need for a machine room above the shaft and the top layer can be installed at a height of more than meters. The computer room can be located within a radius of meters of the shaft, occupying an area of only - square meters. The hydraulic elevator is not equipped with a counterweight device to improve the utilization rate of the shaft area. The load and load cylinder of the hydraulic elevator directly act on the foundation pit, and the strength requirement for the shaft is low. A brick structure or brick concrete structure shaft is sufficient.