Sign in perhaps register 。

Therefore, there are requirements for the service environment of stainless steel, and it is necessary to remove dust frequently and keep it clean and dry.With the implementation of China's reform and opening up, the national economy has achieved rapid growth, and a large number of urban houses, public buildings and tourism facilities have been built, which puts forward new requirements for hot water supply and domestic water supply. In particular, people pay more and more attention to the problem of water quality, and the requirements are also increasing. Galvanized steel pipe, a common pipe, will gradually withdraw from the historical stage under the influence of relevant countries because of its corrosivity. Plastic pipe, composite pipe and copper pipe have become common pipes in the pipeline system. However, under certain circumstances, stainless steel pipe has more advantages, especially the stainless steel pipe with wall thickness of only . ~ mm. In high-quality drinking water system, hot water system and water supply system that puts safety and sanitation first, it has the characteristics of safety, reliability, sanitation, environmental protection economy and applicability. It has been proved by engineering practice at home and abroad that it is one of the new, energy-saving and environmental protection pipes with good comprehensive performance of water supply system. It is also a very competitive water supply pipe,The stainless steel pipe installed on the pipeline support can be corroded by ppm chloride ion and ppm residual chlorine in an aerobic environment. For carbon steel structural supports, the pipeline shall be insulated to prevent corrosion due to potential difference, and the external insulation cotton shall be wrapped for anti-corrosion treatment. Remember, never use glue and other materials that contain chloride ions, halogens and other corrosive effects on stainless steel pipes.Welding high frequency preheating plus three torch argon arc welding, high frequency preheating plus plasma argon arc welding. The progress of combined welding is very significant. As for the combined welding of steel pipe with high-frequency preheating, the weld quality is equivalent to the conventional argon arc welding and plasma welding, the welding operation is complex, and the whole welding is easy to complete automation. This combination is easy to connect with the existing high-frequency welding equipment, with low investment cost and good benefit.Shunpeierke,For business people of course, it is better to spend less under feasible conditions. For goods such as stainless steel pipes, we can often see that there will be packaging film bags on them. Although they are not heavy, if there are a large number of single purchases, they will also produce certain economic expenses, but why do many people clearly dislike this thing on stainless steel pipes, But I have to accept it. Next, xincoral Xiaobian will tell you why stainless steel pipes need packaging bags.The continuous casting of stainless steel pipe fittings is generally matched with the refining furnace,Ellinikon420J2 stainless steel plate, which has strict requirements on the chemical composition and temperature of molten steel; In order to prevent secondary oxidation of molten steel, non oxidation protection pouring is required during continuous casting production; Strict requirements for refractory materials such as ladle, tundish, nozzle and submerged nozzle.Stainless steel pipe, which was consumed and used at the end of the s, is a rebirth group emerging in today's pipe range. It has been widely used in the construction of water supply and direct drinking water pipelines. Stainless steel pipe is durable and has been recognized by the engineering community, and relevant parties are starting from reducing wall thickness and money, so as to facilitate further implementation. In order to promote stainless steel pipe, since the s, China has started to reduce wall thickness and cost; High diameter to wall ratio and high precision & rdquo; The technical effect of stainless steel pipe makes the stainless steel pipe lose its application and expand quickly. There are various connection modes of stainless steel pipes. The rare types of pipe fittings include contraction type, compression type, push type, socket welding type, union flange connection, welding type and derivative series connection mode combining welding with traditional connection. These connection methods have different application ranges according to their principles, but most of them are convenient, firm and reliable. The sealing ring or gasket materials used for connection are mostly silicone rubber,Ellinikon201 magnetic stainless steel, nitrile rubber and EPDM that meet the requirements of national specifications, which eliminates the worries of users. In the construction of water supply pipe system due to the glorious history of galvanized steel pipe, all kinds of new plastic pipes and composite pipes have been lost and developed rapidly, but they are far from fully meeting the needs of water supply pipe system and the national requirements for drinking water and related water quality. In direct drinking water, stainless steel pipe system is undoubtedly one of the best. At present, hotels and public places at the international level have been equipped or are equipped with direct drinking water pipelines. In many cases, stainless steel pipe has more advantages, especially the stainless steel pipe with wall thickness of only . ~ mm has the characteristics of safety, reliability, sanitation, environmental protection, economy and applicability in high-quality drinking water system, hot water system and water supply system that puts safety and sanitation first. It has been proved by engineering theories at home and abroad that it is not only one of the new, energy-saving and environmental protection pipes with good comprehensive function of water supply, which will play an unparalleled role in improving water quality and improving people's living standard.

Stainless steel pipes can be divided into CR series ( Series), Cr Ni series ( Series), Cr Mn Ni series ( Series) and precipitation hardening series ( Series). Series & mdash; Cr Ni Mn austenitic stainless steel series & mdash; Cr Ni austenitic stainless steel.L stainless steel pipe has become a very popular material in the market because of its many advantages. Today, Xiaobian will tell you in detail about L stainless steel pipe installation technology.Since the back is not filled with argon, its advantages are obvious, which is suitable for installation on the construction site. However, due to its structural characteristics, flux cored welding wire has high requirements for welders during operation, with fast wire feeding speed and high wire feeding accuracy. It is difficult to master. Welders should be specially trained and skilled before they can participate in welding in Yangba, Nanjing And foreign construction sites, we have successfully solved the problem that argon cannot be passed through the junction and repair port.Promise and keep promise,Production mode stainless steel pipe can be divided into seamless pipe and welded pipe according to the production mode. Seamless steel pipe can be divided into hot-rolled pipe, cold-rolled pipe,Ellinikon201 stainless steel decorative pipe, cold drawn pipe and pipe. Cold drawing and cold rolling are the secondary processing of steel pipe; Welded pipe is divided into straight seam welded pipe and spiral welded pipe.Model & mdash; High strength cutting tool steel, with slightly higher carbon content, can obtain higher yield strength after appropriate heat treatment, and the hardness can reach hrc. It belongs to hard stainless steel. A common application example is & ldquo; Shaving blade & rdquo;. There are three common models: C and f (easy to process).Clamping connection steps: cut off the pipe according to the required length. When breaking the pipe it shall not be too large to prevent the pipe from being out of round.

After fine tuning the molten steel temperature in the argon blowing station, it is lifted to the ladle rotary table for continuous casting.Total quality management,The petrochemical industry, including the chemical fertilizer industry, has a great demand for stainless steel pipes. Stainless steel pipes are mainly used in this industry, including, , l, etc., with an outer diameter of about ￠ - ￠ and a wall thickness of about mm-mm (generally medium and low pressure transmission pipes with a specification of more than & phi; mm). The specific application fields are: furnace pipes, material transmission pipes, heat exchanger pipes, etc.Since the invention of stainless steel at the beginning of this century, stainless steel has integrated the image of modern materials and the excellent reputation in architectural applications, which makes its competitors envy. Stainless steel will not produce corrosion, pitting corrosion or wear. Stainless steel is also one of the metal materials with high strength. Because stainless steel has good corrosion resistance, it can keep the integrity of engineering design of structural components. Chromium containing stainless steel also integrates mechanical strength and high extensibility, which is easy to process and manufacture parts, and can meet the needs of architects and structural designers.For more than years, architects have been using stainless steel to build cost-effective buildings. Many existing buildings fully illustrate the correctness of this choice. Some are very ornamental, such as the Chrysler Building in New York City. However, in many other applications, but in the aesthetics and performance of buildings For example, it is the preferred material for designers when building sidewalks in places with large population flow.Ellinikon,After molten steel casting stainless steel pipe fittings generally adopt the same vertical, vertical bending or arc continuous caster as carbon steel. The refined molten steel is poured into the ladle, the ladle to be poured is transferred above the tundish mouth through the rotary table, and then the molten steel is tundish through the long nozzle. The molten steel in tundish enters the mold through the submerged nozzle for forming, condensation and continuous downward movement.Restate the quality of stainless steel pipe, such as stainless steel pipe, we promise & ldquo; chromium and nickel & rdquo; Penalty for false and provide quality inspection report and certificate of conformity.Model & mdash; other properties are similar except that the risk of weld corrosion is reduced due to the addition of titanium.