Sign in perhaps register 。

. Raw material problem of stainless steel pipe. If the hardness is too low, it is not easy to polish (BQ is not good). If the hardness is too low, orange peel is easy to appear on the surface during deep drawing, which affects BQ performance. BQ with high hardness is relatively good.Austenitic stainless steel has good resistance to uniform corrosion, but there are still the following problems in local corrosion resistance: intergranular corrosion of austenitic stainless steel. Austenitic stainless steel will have intergranular corrosion when it is kept warm at ~ ℃ or cooled slowly. The higher the carbon content, the greater the tendency of intergranular corrosion. In addition, intergranular corrosion also occurs in the heat affected zone of the weldment. This is due to the precipitation of Cr rich CrC on the grain boundary. The chromium poor area is formed in the surrounding matrix, which is caused by corrosion of the primary cell. This intergranular corrosion phenomenon also exists in the ferritic stainless steel mentioned above.Vari,Manufacturing technology of stainless steel pipe hot rolling（Stainless steel why corrosion-resistant stainless steel decorative pipe, stainless steel pipe, stainless steel pipe,VariStainless steel marine pipe, all metals react with oxygen in the atmosphere to form an oxide film on the surface. Unfortunately, the iron oxide formed on ordinary carbon steel continues to oxidize, expanding the corrosion and finally forming holes. The carbon steel surface can be guaranteed by electroplating with paint or oxidation resistant metals (e.g. zinc, nickel and chromium), but as is known, the steel below begins to rust.Uruzgan province,That is stainless steel. The GB brand is CrNi. & mdash; it has better temperature resistance than it.Stainless steel pipe is a kind of economical section steel and an important product in the iron and steel industry. It can be widely used in life decoration and industry. Many people on the market are used to make stair handrails, window guards, railings, furniture, etc. and materials are common.Combined steel and spring steel, such as CrMnTi simn, (C content is expressed in ten thousandths).

And stainless steel are molybdenum containing stainless steels. The molybdenum content of stainless steel is slightly higher than that of stainless steel. Due to the molybdenum content in stainless steel, when the concentration is lower than % and higher than %, stainless steel has a wide range of applications. Stainless steel also has good chloride corrosion resistance, so it is usually used in marine environment.(V) the profitability of the steel plant has declined month by month. In the first half of , the metallurgical industry realized a profit of . billion yuan, a year-on-year increase of %, of which the ferrous metal smelting and rolling processing industry realized a profit of . billion yuan, a year-on-year increase of %. From January to may, the profitability of key large and medium-sized iron and steel enterprises was far lower than the overall level of the industry, and showed a downward trend month by month. Although the profit increased by %, it was only . billion yuan, with a profit margin of .%. In May, key large and medium-sized iron and steel enterprises realized a profit of only million yuan, falling month on month for five consecutive months, of which suffered losses, with a loss surface of %.The best way to improve the quality of stainless steel pipe fittings is to change the process from ingot to billet. Due to the improvement of continuous casting process, this has become a necessary means to improve product quality.Quality management, the responsibility of the calender is that the annealed steel strip is blackened, the furnace liner is perforated, and ammonia leakage will cause rust. . The responsibility of the steel plant is that the peeling and trachoma of the steel strip will cause rust. Substandard materials will cause rust. the responsibility of the calender is that the annealed steel strip is blackened, the furnace liner is perforated, and ammonia leakage will cause rust. . The responsibility of the pipe manufacturer: the welds in the pipe manufacturer are polished rough, which will cause rust.When improved, it is possible to use it in refrigeration related engineering. Recently, suslx (cr Ti, Nb LC) and susl have been applied to frozen shells. Ferritic stainless steel has body centered cubic structure. When the material properties become weaker sharp cracks will expand rapidly and cause brittleness. Austenitic series stainless steel will not produce brittleness because it has face centered cubic structure. Austrian stainless steel SUSL (cr-ni LC) and SUSL (cr-ni-mo-lc) shows that it still has superior impact characteristics at low temperature. However, pay attention to the precipitation of ferrite or martensite due to processing and the tendency of embrittlement due to sensitized carbide or & sigma; equal heterogeneous precipitation.Martensitic stainless steels typical martensitic stainless steels include Cr ~ Cr and Cr, which have good processing properties. Deep drawing, bending crimping and welding can be carried out without preheating. Crl does not require preheating before cold deformation, but preheating is required before welding. crlcr is mainly used to make corrosion-resistant structural parts such as steam turbine blades, while crcr is mainly used to make surgical and wear-resistant parts of medical instruments; crl can be used as corrosion-resistant bearings and tools.

Accounting for about % - % of the total steel, it is widely used in the national economy. Because the steel pipe has a hollow section, it is suitable for gas and solid transmission pipelines; at the same time, compared with the round steel of the same weight, so it has also become an important material in various machinery and building structures. Stainless steel is used Under the condition of equal weight the structure and components formed by pipe have a larger section modulus than solid parts. Therefore, stainless steel pipe itself is an economic section steel that saves metal. It is an important part of steel, especially in oil drilling, production and metallurgyA complete range of products,VariStainless steel plate coloring,Therefore,VariStainless steel compression tube, there are requirements for the service environment of stainless steel, alkali and salt substances (such as alkali water and lime water splashing on the decoration wall), which leads to local corrosion.Rockwell hardness the Rockwell hardness test of stainless steel pipe is the same as Brinell hardness test. The difference is that it measures the depth of indentation. Rockwell hardness test is widely used at present, and HRC is second only to Brinell hardness Hb in steel pipe standards. Rockwell hardness can be used to measure metal materials from very soft to very hard, It is simpler than Brinell method and can read the hardness value directly from the dial of the hardness machine. However, due to its small indentation, the hardness value is not as accurate as Brinell method.Vari,The manufacturing and maintenance of equipment consume more than tons of stainless steel pipe. This kind of industry mainly adopts sanitary or grade stainless steel pipe. The sanitary seamless pipe made of imported sus and l can meet the special requirements of various media in the field of food and biopharmaceutical. Stainless steel has the advantages and good performance of stainless steel. It is widely used in kitchen equipment, workbench, utensils and medical instruments in the food industry The demand for tableware, towel hanging bracket and bracket of refrigerator in daily life is increasing.Standard classification - classification: national standard GB industry standard Yb local standard enterprise standard qcb- classification: product standard packaging standard basic standard - standard level (divided into three levels): y level: international advanced level I level: international general level H level: domestic advanced level - national standard: stainless steel bar (level I) gb- stainless welding disc Park (level H)Inspection: after crimping, check the crimping size with a special gauge.