Sign in perhaps register 。

　　The high-efficiency slurry pump has three characteristics: first, the slurry pump has high operation efficiency and low loss.　　Head refers to the energy obtained from the pump by the unit weight of liquid output by the pump,Angus afril éPipeline pump, so head refers to the effective energy obtained from the liquid output by the pump in unit time - that is, the effective power of the pump: the equation is PE= ρ GQH (W)= γ QH (W)Angus afril é,　　The motor burns out the winding due to heat dissipation. The water pump shall be lifted and lowered at any time with the change of water level in the well. In case of water reduction or interruption, the cause shall be found out immediately or the pump shall be shut down for inspection. The cable shall not rub against the shaft wall to prevent the well water from penetrating into the motor along the cable core after the cable is worn.　　Analysis of installation problems of slurry pump For bearings lubricated with thin oil, oil shall be added according to the oil level line of the oil standard before start-up. Add (HL hydraulic oil in winter and (hl hydraulic oil in summer. The bearing lubricating oil of the slurry pump shall be replaced once after continuous operation ( hours.Matam,　　The impeller of the submersible slurry pump may need to be disassembled for maintenance or repair during use. However,Angus afril éCirculating hot water pipeline pump, when we do not know the pump structure, we may make mistakes during disassembly. Let&#;s take a look at the correct disassembly of the impeller　　 We also need to make choices according to local conditions when we make purchases at ordinary times. For example, the head of the centrifugal pump itself is relatively high, but its water output is not very large when it is used, so it is effective when it is used in many mountainous areas　　Wheel, corrosion-resistant, non clogging, and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more complete desilting. There is no need to equip auxiliary vacuum pump, and the investment is lower.

　　Under the action of auxiliary devices, it can transport the slurry, and because the sealing device itself is special, it can also ensure the internal and external balance of the submersible slurry pump during transportation, so that the pressure at both ends of the equipment can be balanced during normal use　　 Professional maintenance: if the submersible sewage pump cannot work normally, do not disassemble and repair it without authorization, but carry out professional maintenance immediately.　　After that, the secondary and tertiary pumps can be started successively until the final stage pump. After all the series pumps are started, the outlet valve of the final stage pump can be gradually opened. The speed of opening the valve should be controlled by the fact that the pump does not vibrate and the motor of any stage does not exceed the rated current.quality standard,　　Second the power used is not matched, so the motor temperature will be too high after long-term overload operation; In addition, frequent startup during use will also lead to fever, so I　　 When the power supply voltage is too low, the pump will be overloaded, because the pump is also widely used in many rural watering. In this case, it may be lower than the rated voltage, so the current in the stator winding will also be　　No matter what type of slurry pump you need, Ritter pump will provide you with the highest quality slurry pump products; The latest development of submersible slurry pump technology in recent years The diving depth has increased from meters to meters!

　　Water pump is a kind of machinery that pumps energy liquid. It is a machine that converts the mechanical energy of the prime mover into the potential energy of the pumped liquid. Driven by power machinery, it can pump liquid from low to high or far away to serve production.Fair price,Angus afril éISG single stage vertical pipeline pump,　　Water flow into the bearing damages the bearing.　　 pump room height and allowable lifting height of lifting equipment　　The submersible slurry pump may be blocked when it is used at ordinary times. In particular, some equipment is frequently used at ordinary times, but the maintenance work is not done well when it is used, so it will be blocked after being used for a period of timeAngus afril é,　　The fruit is also bad; When the axial flow pump is used, its water output is relatively large but the head is not too high, it has a great impact on the impeller of the equipment itself. So how to detect whether the equipment has cavitation during use?　　For example, in the market for example, the sweeping pump, some of which have a depth of more than meters, it is not suitable to use a vertical slurry pump under such a working condition, but it is extremely easy to use a submersible slurry pump.