Sign in perhaps register 。

I-beam is an economic section high-efficiency profile with more optimized section area distribution and more reasonable strength weight ratio. It is named because its section is the same as the English letter 'H'. The small length of repair welding is mm; The raw material shall not exceed mm after grinding by welding edge.Leverkusen,Longitudinal welded pipe has the advantages of simple production process, low cost and rapid development. The strength of spiral welded pipe is generally higher than that of straight welded pipe. It can produce welded pipe with larger pipe diameter with narrow blank, and welded pipe with different pipe diameter with blank of the same width. However, compared with the straight seam pipe with the same length, and the production speed is low. Welded pipes with large or thick diameter are generally made of steel blank directly, while small welded pipes and thin-walled welded pipes only need to be welded directly through steel strip. Then after simple polishing, wire drawing is OK. Welded pipe is welded with strip steel, so it is not as high as seamless pipe in its original position. Welded pipe process: uncoiling of raw materials - leveling - end shearing and welding - looper - forming - Welding - removal of internal and external weld beads - pre correction - induction heat treatment - sizing and straightening - eddy current testing - cutting - hydraulic inspection - Pickling - Inspection (strict control) - Packaging - delivery.With the development of steel structure buildings, only I-beam is not enough, that is, thickened I-beam,Leverkusen2205 duplex steel welded pipe, which is easy to lose stability for load-bearing columns.Buguma,The general alloy pipe with improved performance is variable and has high application value. The alloy pipe contains more Cr and is heat resistant Low temperature resistance Corrosion resistance. There is no aluminum alloy in plain carbon seamless steel pipe, not very little aluminum alloy, and the alloy pipe is used in crude oil Aerospace Chemical plant Power engineering heating furnace. Because the physical properties of alloy tubes are easy to change and adjust. Cold extrusion. This kind of processing method is more purposeful. Before the preparation of steel processing and extrusion molding, when the extrusion molding is used for mm diameter pipe fittings, the investment of machinery and equipment is less, so the raw material consumption is also very small, and the technology is relatively perfect. Once the tube size is increased, the cold extrusion method must have large cargo capacity and high-power machinery and equipment. Therefore, the automatic control system will be upgraded.Generally there are many passivation methods for alloy tubes, the common ones are high temperature passivation or sodium cyanide passivation.

The core of C-section steel is the structural system of braced frame. More than half of such senior managers in China are the former. Unfavorable to earthquake resistance. Hydraulic power, generally about KW, which is similar to the plate shearing and bending machine. The general control process is complex, and PLC control is mostly used.On the other hand, when the steel structure changes during heat treatment that is, austenite transforms into martensite, the increase of specific volume will be accompanied by the expansion of workpiece volume, and each part of workpiece will undergo phase transformation successively, resulting in inconsistent volume growth and structural stress. Due to the change of tissue stress, the tensile stress on the surface and the compressive stress in the heart are just opposite to the thermal stress. The magnitude of microstructure stress is related to the cooling rate,LeverkusenAlloy pipe 12Cr1MoVG price, shape and chemical composition of martensitic transformation zone materials.Alloy pipe is a kind of seamless steel pipe. Alloy pipe is divided into structural seamless pipe and high-pressure heat-resistant alloy pipe. It is mainly different from the production standard and industry of alloy pipe. Annealing and tempering of alloy pipe changes its mechanical properties. Meet the required processing conditions. Its performance is higher than that of ordinary seamless steel pipe, its utilization value is higher, the chemical composition of alloy pipe contains more Cr, and its performance of high temperature resistance, low temperature resistance and corrosion resistance. Ordinary carbon seamless tubes do not contain alloy components or have few alloy components. Alloy tubes are widely used in petroleum, aerospace, chemical industry, electric power, boiler and other industries because the mechanical properties of alloy tubes change and are easy to adjust.Quality inspection report,What is the purpose of flat steelThe core of C-section steel is the structural system of braced frame. More than half of such senior managers in China are the former. Unfavorable to earthquake resistance. Hydraulic power and the power is large, generally about KW, which is similar to the plate shearing and bending machine. The general control process is complex, and PLC control is mostly used.b. The professional two-sided arc welding processing technology can complete the electric welding at a good position, which is not easy to have the disadvantages of staggered joint, welding deviation and incomplete penetration, and it is very easy to manipulate the welding quality.

When it is used for ground heating and hot spring transportation,LeverkusenWhich is a good welded pipe manufacturer, it can meet the requirements of refrigeration and achieve the practical effect of less damage. It is applicable to water conservancy engineering, mining and other industries to meet the provisions of cold, cold and corrosion prevention. In addition, the chemical raw material transmission pipeline has a wide indoor space.Potential development,Application scope of alloy pipeThe whole structure is composed of zinc and quaternary crystals, forming dense crystals and barrier layer on the plate, which effectively prevents the penetration of corrosion factors. From the point of view of the strong zinc corrosion resistance of the barrier layer, when the zinc sacrificial anode is at the forefront of protection, the scratches and scratches of some coatings and the insolubility of zinc oxide layer play a protective and blocking role.I-beam: national standard * what is the wall thickness of I-beamLeverkusen,Alloy pipes can be used for heating (cooling) projects.When we carry out different projects, we must use different raw materials, which can ensure the quality of the project. In many kinds of data, alloy pipe is widely used. In many projects, so it is very popular in the field. When people carry out the construction of alloy pipe project there are many things that must be paid special attention to. Let&#;s take you to know:I-beam, also known as steel beam, is a long strip of steel with I-shaped section. I-beam is divided into ordinary I-beam and light I-beam. It is a section steel with I-type section shape.