Sign in perhaps register 。

Vehicle mounted lifting platform is widely used for high-altitude operations in hotels, buildings, airports, stations,SitaFixed electric hydraulic lifting platform, sports venues, workshops, warehouses, and other places; It can also be used as temporary high-altitude lighting advertising, etc.When placing materials on the platform, they should be placed in the middle of the platform as much as possible. The weight of the goods should be within the standard load range of the equipment, and the volume of the goods should not exceed the platform size of the equipment. Otherwise, materials and lifting platforms may be injured and dangerous accidents may occur. High priced and various specifications of elevator manufacturers provide timely supply, with high cost-effectiveness,In case of strong wind of level or above, rainstorm, thunder, fog and other bad weather, the work at heights in the open air shall be stopped at the boarding bridge.The lifting platform is placed on a horizontal support surface, and the concentrated load of MAX load capacity is placed at any position mm away from the periphery of the workbench. After lifting times, each load-bearing component must not have deformation or cracks.Suncheon,Protective device: In case of power or oil circuit failure, there should be a safety rope to prevent the workbench from falling out of control. (Allow controlled descent)The installation personnel should have the qualification for installing hydraulic cargo elevators, carefully implement the special construction plan for installation and construction, and provide safety technical disclosure to the installation personnel for technical design.There is a phenomenon of self stopping when running up and down. Due to poor contact of the safety protection switch, it is easy for hydraulic cargo elevator manufacturers to cause this problem.

Regularly check all wires and cables for damage. It is necessary to wrap and replace the damaged parts in a timely manner.Ensure a good power supply at the installation site, install a separate distribution box, and when using the distribution box,SitaHydraulic lifting platform truck, the electrical leakage switch must meet the requirements for construction elevators. If the installed construction elevator is variable frequency, the leakage switch should be compatible with the frequency converter when selecting it.The noise and oil level of the elevator oil cylinder are too low. From the air at the connection of the oil filter or joint to the oil, the air and oil at the moving shaft are blocked. The oil return pipe of the oil filter is loose, and the air or oil pipe is on the oil surface, Mixing air into the oil to eliminate: The concentricity should be adjusted to within .MM. The coupling should be repaired or the oil pump should be replaced to increase the oil volume above mm in the oil filter and joint positions. The rotating shaft sealing ring should be replaced to clean the oil filter screen, filter the oil, and extend the return oil pipeline below the oil level. If there is air mixed in the oil or the air in the hydraulic cylinder is not completely discharged, it will cause cavitation under high pressure and cause significant noise. At this point, it is necessary to exhaust the air in a timely manner.Latest quotation,The characteristics of the platform include reliable hydraulic system, simple operation, large load-bearing capacity, and rear hinge support.Regularly check the operation of each mechanism for normal operation and noise. If any faults are found the hydraulic cargo elevator wholesale should be promptly eliminated. Otherwise, it will affect the use of the guide rail hydraulic lifting platform. When refueling, the hydraulic oil should be filtered and filled, and the refueling tools should be reliable and clean. The hydraulic cargo elevator manufacturer should not remove the filter at the fuel tank filler to improve the refueling speed. Refueling personnel should use clean gloves and work clothes to prevent solid and fiber impurities from falling into the oil.Regularly check whether each organization is functioning properly and whether there is noise. If problems are found, they should be promptly cleaned up.

Emergency descent device: When a power driven chain elevator loses power, there should be a device to make the workbench emergency descend.Home page recommendation,When the hydraulic system malfunctions, the hydraulic elevator may experience problems with the hydraulic pump motor, valve, and hydraulic installation after repairing the hydraulic system, which can easily cause vibration and generate significant noise.High altitude work should always use tool bags. Tools with larger boarding bridges should be tied to sturdy components with ropes, and should not be placed randomly to prevent accidents caused by falling from a height.When the hydraulic oil of the equipment is insufficient, it will not cause lifting. At this point, you only need to add enough hydraulic oil to run.Sita,The hydraulic oil used in the system has the same brand, and the oil temperature is between ~ ℃. Use a large flow rate to remove impurities from the system as much as possible. The hydraulic system needs to be cleaned repeatedly three times or more, and after each cleaning the system should be drained while the oil is hot. After cleaning, clean the filter and add new oil after using a new filter element.When the hydraulic system malfunctions, the hydraulic elevator may experience problems with the hydraulic pump, valve, and hydraulic installation after repairing the hydraulic system, which can easily cause vibration and generate significant noise.Regularly check whether each organization is functioning properly and whether there is noise. If problems are found, they should be promptly cleaned up.