Sign in perhaps register 。

it will certainly do more work. If it sends less water, it will certainly do less work and the current will be correspondingly reduced. Pump power (kw) = head (m) × Flow (m/s) × The gravity of the fluid (kg/m for water) divided by (power conversion factor) divided by the efficiency of the pump (about　　All kinds of newly designed mechanical seals of submersible slurry pumps contribute greatly to the growth of market share.Fracha,　　The industry is facing new technological innovations. Enterprises have also launched their own killer maces in the competition, constantly improving their R & D teams and studying the related core production technologies, so as to improve the competitiveness of enterprises in the market.　　 Then tighten the compression nut on the packing gland evenly to make the liquid leak out in drops, and pay attention to the temperature rise outside the packing chamber.El Tigre,　　 there is also a simple method to measure the vibration frequency of the pump by vibration method. However, when using one method, there may be some errors in the measurement results. When many equipment are used, in fact, make sure that the liquid in the submersible slurry pump is completely discharged. If the rotor is disassembled, drain the lubricating oil in the rotor bearing housing. If the newly added oil is stored, it should continue to be used after maintenance. Do not dump it directly　　The vertical sand pumping pump is popular with a wide range of sand pumping pump users because it is easy to move. This equipment is made of high-tech endurance data. Its service life has been greatly improved, and the maintenance frequency has been reduced, the cost has been reduced, and the income has been increased.

　　This phenomenon shows that the failure of the pump is not only a material problem, but also reminds the pump designers and producers that in addition to good working conditions,FrachaHorizontal slurry pump, the pump should also have good corrosion resistance, high reliability and long service life. The pump shall be designed in addition to the conventional design method of fluid mechanics　　 Realize centralized management. In the application of multiple fire pumps, the deployment of fire pumps may be decentralized, and the working environment of fire pumps is often complex, so it is very difficult to adopt manual management. cf fire control cabinet can realize centralized management of multiple fire pumps, with operation　　 First remove the pump from the engine.Potential development,　　When using the sand pump be sure to pay attention to the steering divergence between the motor and the pump. The sand pump has an arrow on the pump to mark the main steering. After the power supply is connected, run the pump without load. Check whether the motor operates normally. During operation, be careful not to exceed the bearing on the pump support to avoid　　Although the shaft seal occupies a small position in the pump, the normal operation of the pump is closely related to the shaft seal.　　 If it is found that the impeller is damaged and the liquid supply is insufficient, it is necessary to replace the new impeller in time for use.

　　Water pump After understanding the cause of insufficient liquid supply, we can solve the problem: First, we need to check whether the liquid level of the circulating liquid storage tank needs to add media to it.For more, please check,　　 install a valve to inject water at the water inlet and outlet. This method is to install a valve on the water inlet pipe of the submersible slurry pump and connect the water pipe to inject water into the pump. This is a common and simple method.　　Whether the pipeline pump can absorb water and whether the pipeline pump has self-priming depends on the model of the pipeline pump. Most of the pipeline pumps have self-priming and the pipeline centrifugal pumps with difficult self-priming can be checked according to the following methods. For longer use　　 the water pipe shall be short, and the cavitation allowance of the device shall be greater than that of the pump. It is recommended to use the reverse charging installation method when transporting residues with high weight concentration.Fracha,　　 When the power supply voltage is too low, the pump will be overloaded,FrachaSubmersible non clogging sewage pump,FrachaBooster pipeline pump, because the pump is also widely used in many rural watering. In this case, it may be lower than the rated voltage, so the current in the stator winding will also be　　Submersible slurry pump In addition, it must be used continuously during transportation. If there is an interval in the middle, it must be avoided that the interval is relatively long, so as to avoid the solidification of slurry in the pump when the operation is stopped.　　 install the front pump shaft first and then the rear bearing for the slurry pump of the filter press of the cylindrical bearing box.