Sign in perhaps register 。

Editor's note on the causes of steel rusting: chloride ions exist widely, such as salt, sweat stains, seawater, sea breeze, soil, etc. stainless steel corrodes rapidly in the presence of chloride ions even surpassing ordinary low-carbon steel. Chloride ions form complexes with Fe in alloy elements, reducing the positive potential of Fe, and then being stripped of electrons and oxidized [].Rheological and thermal changes in the quenching process of decorative stainless steel pipe the cooling characteristics of submerged quenching of stainless steel plate are numerically simulated by using the Euler multi fluid model in AVL fire software, and the numerical results are compared with the experimental results. In the research, the quenching medium is water. The mass, momentum and energy equations of gas-liquid two-phase of quenching medium and the quenching heat conduction equation of stainless steel workpiece are solved by numerical simulation. Based on the principle of equal heat flux between quenching medium and workpiece,Salgotarjan304 stainless steel square tube, the temperature field of quenching medium and workpiece is solved by coupling. The comparison between the numerical simulation and experimental results of decorative stainless steel pipe shows that the numerical simulation results of workpiece temperature are in good agreement with the experimental data. The model can reliably simulate the quenching process of workpiece, and can be extended to the multiphase flow simulation in complex system to guide the actual production. The single pass thermal simulation compression experiment of Cr super martensitic stainless steel was carried out by Gleeble thermal simulation tester to study the thermal deformation behavior at ~ ℃ and strain rate of . ~ s-, and the microstructure evolution law of grains under different conditions was analyzed; Based on Sellars hyperbolic sinusoidal model the flow stress constitutive equation of Cr super martensitic stainless steel was constructed. The results show that the peak stress decreases with the increase of deformation temperature and the decrease of strain rate; With the increase of deformation temperature, the grain grows and coarsens gradually. With the increase of strain rate the dynamic recrystallized grains are obviously refined. The thermal deformation activation energy Q = . JMOL of decorative stainless steel pipe is calculated, and the expression of Zener Hollomon parameter is obtained. Different feedstocks were prepared by mixing crmnmon nickel free austenitic stainless steel powder prepared by aerosol and wax based binder. The effects of binder ratio and powder loading on the rheological properties of feed were studied by rh high pressure capillary rheometer. Non Newtonian index n, viscous flow activation energy E and comprehensive rheological factor alpha are calculated by second order model regression analysis; STV. The results show that the prepared feeds are pseudoplastic fluid. The binder system was composed of % microcrystalline wax (MW), % high density polyethylene (HDPE), % ethylene vinyl acetate copolymer (EVA) and % stearic acid (SA). The powder loading was vol%. The feed had good comprehensive rheological properties. In order to study the cementitious properties of stainless steel AOD slag, stainless steel AOD slag was used to replace some cement, and its effects on the working properties and mechanical properties of cement mortar were studied. The results show that using stainless steel AOD slag to replace cement from ~ %, with the increase of the content of stainless steel AOD slag, the water consumption of standard consistency of cement first decreases and then increases. When the content is %, the water reduction effect of stainless steel AOD slag is good; With the increase of the content of stainless steel AOD slag, the strength of cement mortar decreases in turn, indicating that the cementitious activity of stainless steel AOD slag is small.Salgotarjan,Hot rolled stainless steel tubes are generally produced on automatic tube rolling mills. After inspection and removal of surface defects, the solid pipe blank is cut into the required length, centered on the end face of the perforated end of the pipe blank, and then sent to the heating furnace for heating and perforated on the piercer. During perforation, a cavity is gradually formed inside the pipe blank, which is called rough pipe. Then it is sent to the automatic pipe mill to continue rolling. After that, the wall thickness of the whole machine is adjusted, and the diameter is determined by the sizing machine to meet the specification requirements. It is advanced to produce hot rolled seamless steel pipe by continuous pipe mill.Refining and transportation industries are in great demand. Secondly, geological drilling, construction industry, machinery industry, aircraft and automobile manufacturing, boiler, medical equipment, furniture and bicycle manufacturing also need a large number of various steel pipes. With the development of new technologies such as atomic energy, rocket, missile and aerospace industry, stainless steel pipe plays an increasingly important role in national defense industry, science and technology and economic construction.Courcelles,Brinell hardness in stainless steel pipe standards, Brinell hardness is widely used,SalgotarjanStainless steel pipe holder, and the hardness of the material is often expressed by indentation diameter, which is intuitive and convenient. However, it is difficult to vent on the inner side, and some sides are easy to be blocked. In this case, water-soluble paper + blocking plate can be used for blocking. That is, the easy to vent and good side can be blocked with blocking plate, the difficult to vent and bad blocking plate side can be blocked with water-soluble paper, and the weld on the outer side can be blocked with adhesive tape (see Table ) .Stop the written technical disclosure, on-site technical and safety disclosure to the on-site operators.

It has the characteristics of high efficiency and low cost. At the same time, it can also well ensure the welding quality (in the capacity expansion and reconstruction project of Urumqi petrochemical, we use this method to weld joints and repair joints, with a one-time qualified rate of welding), which is worthy of our use.Since last year, foreign countries have frequently carried out & ldquo; Double inverse & rdquo; This has a great impact on China's stainless steel casting industry. Export is a large part of the development of China's stainless steel industry and occupies a huge market share in its industrial development. In the face of the current economic downturn and slow development speed, the development of China's stainless steel industry should continuously improve product quality, Better develop overseas trade and deal with trade protectionism, combine products with environmental protection, energy resources and cultural environment, and improve the competitiveness of stainless steel products. Only in this way can we achieve an invincible position in foreign trade.According to the purpose, it can be divided into oil well pipe (casing, oil pipe and drill pipe) pipeline pipe, boiler pipe, mechanical structure pipe, gas cylinder pipe, geological pipe, petroleum cracking pipe) and marine pipe.Online consultation,Model & mdash; other properties are similar except that the risk of weld corrosion is reduced due to the addition of titanium.Shape, stress, temperature and metal flow of forgings and dies. Results the multi-step upsetting extrusion process under high temperature can make the end of steel pipe meet the forming requirements. Conclusion the plastic forming process of steel pipe end is feasible, which has important reference significance for the improvement of pipe connection mode of railway freight car braking system.Welding of stainless steel pipe argon arc welding stainless steel pipe: it is required to have deep penetration, no oxide inclusion, and the heat affected zone can be as small as possible. Argon arc welding maintained by tungsten inert gas has good compliance high welding quality and good penetration function. Its commodities are widely used in chemical, nuclear and food industries.

The best way to improve the quality of stainless steel pipe fittings is to change the process from ingot to billet. Due to the improvement of continuous casting process, this has become a necessary means to improve product quality.Process inspection,Duplex stainless steel product description: This stainless steel has good corrosion resistance in urea carbamate solution and high stress corrosion cracking resistance in chloride environment. At the same time, the duplex stainless steel has excellent mechanical properties and can be used in plant construction with high safety requirements.(V) the profitability of the steel plant has declined month by month. In the first half of ,Salgotarjan20 large diameter seamless steel pipe, the metallurgical industry realized a profit of . billion yuan, a year-on-year increase of %, of which the ferrous metal smelting and rolling processing industry realized a profit of . billion yuan, a year-on-year increase of %. From January to may, the profitability of key large and medium-sized iron and steel enterprises was far lower than the overall level of the industry, and showed a downward trend month by month. Although the profit increased by % it was only . billion yuan, with a profit margin of .%. In May, key large and medium-sized iron and steel enterprises realized a profit of only million yuan, falling month on month for five consecutive months, of which suffered losses, construction industry.Salgotarjan,Model & mdash; Commonly used precipitation hardening stainless steel model, usually also called -; %Cr,%Ni.Stainless steel grade group Series & mdash; Chromium nickel manganese austenitic stainless steel series & mdash; Chromium nickel austenitic stainless steel model & mdash; Good ductility, used for molding products. It can also be machined to harden rapidly. Good weldability. The wear resistance and fatigue strength are better than those of stainless steel.The intergranular corrosion of austenitic stainless steel can be prevented by adding Ti, Nb and other elements that can form stable carbides (tic or NBC) and avoiding the precipitation of crc on the grain boundary.