Sign in perhaps register 。

　　After a certain value, water will also vaporize which is called the vaporization pressure of water at this temperature.　　It is also necessary to clean the ventilation duct to avoid blockage.Crayfield,　　 Store in a well ventilated and dry place. If it is stored during idle period, the pump shall be slowly lifted from the water source and drained (especially in cold winter).　　Stop, press down the nut, and fix the axial position of the rotor. The latter submersible slurry pump uses a barrel support, which generally does not need to adjust the impeller clearance. Therefore, if there is a problem with the clearance in the future use, loosen the support clamp first, and say that the nut is looseAsh Shatrah,　　Pressure. Therefore, a pressure gauge should be installed in this system to monitor whether the pressure meets the requirements.　　Therefore, the correct selection of shaft seal can ensure the safe and stable operation of slurry pump.　　 Assembly of rotor parts of submersible slurry pump Before assembly,CrayfieldSubmersible sewage pump, apply a layer of lubricating oil on the mounting surface to protect the shaft hole from damage.

　　First, the reason for the motor body: the wrong connection will make the temperature rise rapidly when the equipment is used; In addition, there may be some phase to phase short circuits between stator windings, so when the situation is relatively minor, Li is a centrifugal pump. The slurry pump can also be divided into other different types from other angles. Let&#;s see from what angle Panshi pump can classify the slurry pump: first, the suction inlet of the slurry pump　　In fact the impeller clearance of submersible slurry pump is not adjustable for all types of pump, but it is adjustable. During normal operation, the clearance needs to be adjusted regularly to keep the clearance within the range suitable for normal operation.Price,CrayfieldISG single stage vertical pipeline pump,　　 Before starting the submersible slurry pump, the rotor of the rotating pump shall be smooth and even, the outlet sluice valve shall be closed, and water shall be injected into the pump to ensure that the pump is full of water without air.　　There will be no insufficient liquid supply or other problems.　　 The rotor assembly is designed according to the actual situation, and the operation is more stable!

　　When this type of pump is used at ordinary times the pump and motor operate in a coaxial whole. When it runs, the motor shaft will drive the impeller of the pump to rotate, and then at this time, the rotating force can be brought to the medium, so thatWork courses,　　 If there is no corresponding water leakage sensor, it is necessary to regularly maintain the submersible slurry pump and replace the seals.　　 Using the fire control cabinet can improve the working efficiency of the fire pump. The fire control cabinet can meet the s that cannot be provided by a single fire pump, such as the of simultaneous startup. In some dangerous situations, a single fire pump can not meet the needs, and multiple fire pumps are required to work at the same time,　　Then it can enter into the volute pump housing. Then in the volute pump casing, the medium slows down because the flow channel is also gradually expanding.Crayfield,CrayfieldLong shaft submerged slurry pump,　　Submersible slurry pump In addition, the sewage pump is usually driven by a motor, which also requires some time og quantity when switching on and off, so in fact, it can be adjusted to a certain extent during use. The submersible slurry pump needs to use a line when in use　　 Precautions for disassembly of submersible slurry pump Before disassembling the filter press, make sure that the liquid in the submersible slurry pump is completely discharged. If the rotor is disassembled, drain the lubricating oil in the rotor bearing housing. If the newly added oil is stored, it should continue to be used after maintenance. Do not dump it directly　　 There is also a vibration method to measure the vibration frequency of the pump, and the measurement is relatively simple. However, when using one method, there are other vibration sources that will affect the measurement results, so it is actually the main