Sign in perhaps register 。

Square tubes are classified by forming: forged steel; Cast steel; Hot rolled steel; Cold drawn steel.If the re inspection results are unqualified (including the items whose preliminary inspection results are unqualified and re inspection is not allowed), the supplier can submit them for acceptance one by one; Or re conduct heat treatment (the number of RE heat treatment shall not exceed times), and propose acceptance with a new batch.Aquintel,From the perspective of production, the temperature of no open forging and final forging is a comprehensive technical and economic problem. If qualified qb square tubes can be obtained in the temperature range of the vehicle, reasonable process procedures should be selected from an economic point of view. Obviously, the higher the temperature, the easier the forging and the higher the productivity,Carbon steel classified by chemical composition: square tube A. low carbon steel (C & le; .%); b. Medium carbon steel (C & le; . ~ .%); c. High carbon steel (C & le; .%).The pressurization size and time are the key to the success or failure of welding. If the square tube synthetic material is not pressurized, a large number of pores will be caused due to the pores of the material itself and the gas generated in the reaction. It is not allowed to leave the reactants in the weld, so it must be densified, usually pressurized during the reaction.Square tube, modified square tube, square tube, QB square tube and hot-rolled square tube are qualified in quality inspection. The manufacturer adopts advanced equipment to ensure the quality of each product. Magnetic flux leakage testing for surface defects of square tubes is very similar to magnetic particle testing for square tubes, and its scope of application, sensitivity and reliability are stronger than magnetic particle testing. Indirect square forming process the traditional forming process of cold-formed square pipe is to gradually roll the hot-rolled steel coil multi stand forming unit into round pipe at room temperature, and then the shaping unit will roll the round pipe into square pipe, which is called indirect square forming process. The traditional roll forming process uses the method of fixed bending point position and variable bending radian to complete the corner forming of pipe blank, which is suitable for rolling small and medium-sized products. Rolling with this process & ldquo; Superb & rdquo; Square tube will show its inherent defects. Because the roll work in the bending process of this process is always concentrated at the point, excessive stress concentration often shows microcracks in the bending process of profiles, which will lead to cracking in serious cases. The products with such defects have serious consequences when they are used in building steel structures. The study of the broken square tube column in the Hanshin earthquake in Japan shows that the corner microcrack is the main cause of the square tube fracture. At the same time, due to the different forming bending radians of products with different wall thickness, the universality of rolls is limited. The large-size cold-formed square tube used in the process adopts the advanced & ldquo; Direct Square & rdquo; The production process is to directly roll the hot-rolled steel coil into a square and rectangular shape at room temperature.

The load of impact toughness acting on the parts at a great speed is called impact load. It is specialized in products and renewable resources. Its business includes: square tube square tube, seamless square tube, galvanized square tube and galvanized tube. The ability of metal under impact load is called impact toughness.Shot blasting is commonly used to clean the surface of castings or strengthen the surface of square tubes. special shaped square pipe is the general name of square pipes with other cross-section shapes except circular pipe. According to the different cross-section shape and size of steel pipe, it can be divided into special-shaped square pipe with equal wall thickness (code D), special-shaped square pipe with unequal wall thickness (code BD) and special-shaped seamless steel pipe with variable diameter (code D) These special-shaped large-diameter qb square tubes are widely used in various structural parts, tools and mechanical parts. Compared with circular tubes, special-shaped tubes generally have large moment of inertia and section modulus, and have large bending and torsion resistance, which can greatly reduce the structural weight and save steel. Square tubes are an indispensable part of construction workbuild,There are many ways of ignition,Aquintel2-inch galvanized round pipe, such as arc, electric spark, flame, strong current, high-temperature furnace, electron beam, laser, high-temperature radiation, microwave, chemical furnace, etc.Reinforcing phases such as reinforcing particles, short fibers and whiskers can be added to the solder to form composites.Impact toughness the load acting on the machine part at a great speed by QB is called impact load, and the ability of metal under impact load is called impact toughness.

It is the process of drawing the die hole of the rolled metal blank (shape, pipe, product, etc.) into a section to reduce the length and increase. It is mostly used for cold processing.quality, Fangguan hasSquare tubes for low and medium pressure boilers (gb-) are high-quality carbon structural steel hot-rolled and cold drawn (rolled) square tubes for superheated steam tubes, boiling water tubes for low and medium pressure boilers of various structures and superheated steam tubes,AquintelSpecification of galvanized square pipe,AquintelConnection mode of galvanized square pipe, large smoke tubes, small smoke tubes and arch brick tubes for locomotive boilers. Square tubes for high-pressure boilers (gb- is a high-quality carbon steel, alloy steel and stainless heat-resistant steel square tube for the heating surface of water tube boilers with high pressure and above. High pressure square tube for chemical fertilizer equipment (GB - is a high-quality carbon structural steel and alloy steel square tube suitable for chemical equipment and pipelines with working temperature of - ~ ℃ and working pressure of ~ mA.AquintelForging square tube: a kind of pressure processing in which the reciprocating impact force of the forging hammer or the pressure of the press changes the blank into the shape and size we need. It is generally divided into forging and die forging. It is often used to produce large-scale materials and materials with large square tube size.Steel for construction and engineering according to the classification of use without phase transformation or partial phase transformation of square tube: A. ordinary carbon structural steel; b. Low alloy structural steel; c. Steel reinforcement.With the progress of the times and the development of science and technology, square tubes will also rust for a long time. How to improve the rust resistance of square tubes and what are its rust resistance? Let me give you a detailed introduction below.