Sign in perhaps register 。

C-section steel has uniform zinc layer, smooth surface,IoniaAlloy pipe, strong adhesion, no zinc scar, no zinc leakage and high dimensional accuracy. All surfaces are wrapped by zinc layer, and the zinc content on the surface is usually -g /? It has long service life, corrosion resistance and durability. It is a kind of stronger protection.Its heat sealing effect is remarkable. It can be directly buried immediately, which can not only save resources, but also reduce consumption, not occupy the natural environment, but also purify the environment. The transportation of gas can meet the requirements of long-distance transportation, prevent actual operation and maintenance, reduce heating equipment, unique and convenient installation, and reduce the construction cycle time of the project. On the whole, it is more convenient to use. It can also be used for the transportation of floor heating and hot springs.Ionia,The electric welding reinforcement mesh can reduce the damage and consumption to the reinforcement processing process. According to statistics, after deducting the steel consumption increased by unit lapping, it can also save about % of the steel. After it is transported to the site according to the construction degree of the project it can be hoisted to the working face. There is no need to set a reinforcement processing site on the site, it can also solve the problems of noise pollution caused by straightening reinforcement. Hot hole breaking cold rolling method. This method is dominated by expansion and expands vertical sliding and skew rolling. The former one is mainly cold rolling by relatively limited mandrel mill which saves the site and increases the management level of the site. At the same time,IoniaWhat is the price of 273 seamless pipe, cold rolling by few station mandrel mill, cold rolling by three high limited mandrel mill and cold rolling by fluctuating mandrel mill. In this way, the advantages of high efficiency, low metal material consumption, excellent product quality and excellent automatic control system are more and more widely used. The competitive advantage of the latter one is low cost and short whole process. It is suitable for the processing and manufacturing of CrMoG alloy pipes with large quantities, small types, multi specifications and high precision. Therefore, it is widely usedTezinets,The production process can be summarized as follows: pre leveling → finishing → straightening → post leveling. Flat steel / A / B steel with width of -, thickness of -, rectangular section and slightly pure edge. Flat steel can be finished steel, or it can be used as blank for welded pipe and thin slab for laminated thin plate.→ under the same section load, the weight of hot-rolled H steel structure is reduced by % - % compared with the traditional structure.c. quality inspection is carried out for alloy pipes,IoniaWhich galvanized pipe manufacturer is good, so that the whole process of steel pipe processing is under reasonable inspection and supervision, and the product quality is reasonably guaranteed.

Key technical characteristics of alloy pipe Application of galvanized pipeThe working principle of flat steel finishing machine in I-beam production process is to pre level and finally level the cold flat steel with two groups of leveling wheel sets staggered up and down in the thickness direction; A pair of finishing wheels arranged relatively are used to extrude the width direction, so that the width is compressed to achieve the expected parameters, and the compression amount is adjustable; Straighten the width with staggered straightening wheels.project,All the cracks occur at -mm away from the edge below the alloy pipe, and the macroeconomic orientation is vertical to the cold rolling orientation, showing a 'high mountain' shape.Dehydrogenation solution: the alloy pipe shall be dehydrogenated after passivation treatment to avoid alkali embrittlementH-shaped steel groove is deep and thick, and can withstand forces in two directions.

Plan scheme : high carbon steel with carbon content exceeding .% and alloy pipe with chromium content not less than %Price,I-beam is mainly used in building structure, curtain wall engineering, mechanical equipment and vehicle manufacturing. There is a great demand for welded steel mesh in China&#;s market.Whether I-section steel is ordinary or light, due to the relatively high and narrow section size, there is a large difference in the moment of inertia between the two main sleeves of the section. Therefore, it can only be directly used for members bent in the plane of their web or form lattice stress members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application.Ionia, insulated and cooled in a certain medium and their metal properties are controlled by changing the metallographic structure on the surface or inside of the material. During the heating and cooling process of structural welded steel pipe workpiece, due to the inconsistency of cooling speed and time between the surface and the core, the temperature difference will be formed, that is, thermal stress.Some applications of I-beam: