Sign in perhaps register 。

C-section steel has uniform zinc layer, smooth surface, strong adhesion, no zinc scar, no zinc leakage and high dimensional accuracy. All surfaces are wrapped by zinc layer, and the zinc content on the surface is usually -g /? It has long service life, corrosion resistance and durability. It is a kind of stronger protection.Under the action of thermal stress, because the initial temperature of the surface layer is lower than that of the heart and the shrinkage is greater than that of the heart, the heart is pulled. At the end of cooling, because the final cooling volume shrinkage of the heart cannot be carried out freely,GalatsonHow much is a 50 steel bar cutter, under the action of thermal stress, the surface of the workpiece is finally compressed and the center is pulled. This phenomenon is affected by factors such as cooling rate, material composition and heat treatment process. The faster the cooling rate the higher the carbon content and alloy composition, the greater the uneven plastic deformation caused by thermal stress during cooling, and the greater the final residual stress. On the other hand, due to the change of microstructure during heat treatment, i.e. the transformation from austenite to martensite, the increase of specific volume will be accompanied by the expansion of workpiece volume and each part of workpiece will undergo phase transformation successively, resulting in inconsistent volume growth and structural stress. The final result of the change of tissue stress is the tensile stress on the surface and the compressive stress in the center, which is just opposite to the thermal stress. The microstructure stress is related to the cooling rate, shape and chemical composition of the workpiece in the martensitic transformation zone.Galatson,The storage of galvanized pipes should pay attention to several points. The first is the storage location. It cannot be placed in the open air, because in the open air, not only the safety of various products such as theft, but also corrosion problems will occur. Open air sites are vulnerable to various extreme weather conditions. Large amounts of rain or snow will erode the zinc coating on the surface to the greatest extent, which may lead to rust of the product. The second is the details of storage. It is not directly exposed to the sun. It shall be cooled and dried and shall not be stored with corrosive articles.The shape of I-beam is similar to that of H-beam. What is the difference between them?Evergem,Alloy pipes can be used for heating (cooling) projects.I-beam is an economic section high-efficiency profile with more optimized section area distribution and more reasonable strength weight ratio. It is named because its section is the same as the English letter 'H'.All the cracks occur at -mm away from the edge below the alloy pipe, and the macroeconomic orientation is vertical to the cold rolling orientation, showing a 'high mountain' shape.

b. The professional two-sided arc welding processing technology can complete the electric welding at a good position, which is not easy to have the disadvantages of staggered joint, welding deviation and incomplete penetration, and it is very easy to manipulate the welding quality.Seamless pipeAlloy pipe is a very important way and type of seamless steel pipe. Its use is relatively common. It is widely used in various engineering projects, manufacturing and key marketing of alloy pipe, That is, many stages of production and processing are not done well. Another is that the seasoning is not enough and the proportion of chemical molecules is wrong. There are all reasons.DiscountWhen we carry out different projects, we must use different raw materials which can ensure the quality of the project. In many kinds of data, alloy pipe is widely used. In many projects, we will apply it, so it is very popular in the field. When people carry out the construction of alloy pipe project, there are many things that must be paid special attention to. Let&#;s take you to know:Aiming at the connective tissue and texture produced in stainless steel plate Position and other crystal defects are generally removed by heat treatment processes such as quenching or quenching. The effect of quenching is to optimize the crystal, eliminate structural defects, reduce strength, and also conducive to cold drawing. In the production and manufacture of cold drawn alloy pipe, quenching machinery and equipment cannot be lacked. Therefore, the formulation of appropriate annealing process is a necessary condition to ensure that the alloy pipe mechanism meets the standard and the commodity does not crack. If the manufacturer in order to better one sidedness, reduce the product cost and reduce the quenching process, it will eventually lead to bad harm to the product quality.Its heat sealing effect is remarkable. It can be directly buried immediately, which can not only save resources, but also reduce consumption, not occupy the natural environment, but also purify the environment. The transportation of gas can meet the requirements of long-distance transportation, prevent actual operation and maintenance, meet the requirements of thermal insulation and cold protection, reduce heating equipment, unique and convenient installation, and reduce the construction cycle time of the project. On the whole, it is more convenient to use. It can also be used for the transportation of floor heating and hot springs.

I-beam is mainly divided into ordinary I-beam,GalatsonHow much is 325 welded pipe, light I-beam and wide flange I-beam. According to the height ratio of flange to web, it is divided into wide, medium and narrow flange I-beams. The specifications of the first two are -, that is, the light I-beam has narrow flange, thin web and light weight. Wide flange I-beam, also known as H-beam, is characterized by two parallel legs and no inclination on the inner side of the legs. It belongs to economic section steel and is rolled on four high universal mill, so it is also called 'universal I-beam'. Ordinary I-beam and light I-beam have formed national standards.management,Ways to obtain surface compressive stress characteristics of alloy tubes Cleaning: first clean the grease, profiled steel plate, etc.). Due to the reasonable section shape, they can make the steel give more play to its performance and improve the cutting capacity. Different from ordinary I-type, the flange of H-section steel is widened, and the inner and outer surfaces are usually parallel, so it is convenient to connect with other components with high-strength bolts. Its size composition is reasonable, series and models are complete, which is convenient for settingGalatson, Small longitudinal crackHeating surface tubes for low and medium pressure boilers (working pressure is generally not greater than MPA and working temperature is below ℃);Application characteristics of I-beam