Sign in perhaps register 。

Using alloy pipe to produce ring parts can improve the utilization rate of raw materials, simplify the production and manufacturing process, and save raw materials and production and processing construction time, such as roller bearing ring throwing Nowadays, seamless steel pipe has been widely used to produce hydraulic jack sleeve.The delivery length of I-beam is divided into fixed length and double length and the allowable difference is specified in the corresponding standards. The length selection range of domestic I-beam is divided into -, - and - according to different specification numbers. The length selection range of imported I-beam is generally -.Ashburn,The production of plastic impregnated welded steel wire mesh is to immerse the formed welded steel wire mesh into a stone groove filled with PVC powder. The dry forming process is complex and the cost is much higher than that of spray welded mesh. Due to different application ranges and different uses, the choice is expensive or cheap, which needs to be determined according to its actual use.Alloy pipe is a spiral seam seamless steel pipe, which is made of hot-rolled strip steel coil, often processed by warm extrusion and welded by automatic double wire double side arc welding process. The alloy pipe sends the hot-rolled strip steel to the welded pipe unit, and the hot-rolled strip steel is extruded through multiple passes. The hot-rolled strip steel is rolled slowly to produce annular pipe material with open mouth gap. Adjust the reduction amount of the extrusion roll to control the welding gap at ~ mm and make both sides of the weld flush.Vijayawada,When we carry out different projects, we must use different raw materials, which can ensure the quality of the project. In many kinds of data, alloy pipe is widely used. In many projects, we will apply it, there are many things that must be paid special attention to. Let&#;s take you to know:H-section steel belongs to high-efficiency and economic cutting profile (other cold-formed thin-wall section steel, profiled steel plate, they can make the steel give more play to its performance and improve the cutting capacity. Different from ordinary I-type, series and models are complete so it is convenient to connect with other components with high-strength bolts. Its size composition is reasonable and the inner and outer surfaces are usually parallel, which is convenient for settingBecause the section size of ordinary I-beam and light I-beam is relatively large and narrow, the moment of inertia of the two main shafts on the section is quite different, which limits its application range. I-beam shall be selected according to the requirements of design drawings. In the structural design, the use of I-beam should be reasonably selected according to the mechanical properties, chemical properties, weldability and structural size of I-beam.

The shape of I-beam is similar to that of H-beam. What is the difference between them?They do not need to protect them from mechanical damage. The small length of repair welding is mm; The raw material shall not exceed mm after grinding by welding edge.Latest quotation,Heating surface tubes for low and medium pressure boilers (working pressure is generally not greater than MPA and working temperature is below ℃); Cross rolling pass system. This pass system refers to that the two open legs of the I-beam pass are not on the same side of the waist at the same time, and the waist has an included angle with the horizontal axis.Classification introduction

GB No. I-beam is in height, in leg width and in waist thickness.Welcome calls ,What should we pay attention to in the production of alloy pipeDuring the heating and cooling process of structural welded pipe workpiece, due to the inconsistent cooling speed and time of surface layer and core layer, the temperature difference will be formed, resulting in uneven volume expansion and contraction,Ashburn40Cr alloy pipe manufacturer, resulting in stress, namely thermal stress. Under the action of thermal stress,AshburnCold drawn welded pipe manufacturer, the starting temperature of the surface layer is lower than that of the core layer, and the shrinkage is greater than that of the core layer, making the core layer stretch. At the end of cooling, the surface layer is compressed and the core is stretched because the cooling volume contraction of the core cannot be carried out freely. That is, under the action of thermal stress, the surface of the workpiece is compressed and the core is pulled.Alloy pipe is a very important way and type of seamless steel pipe. Its use is relatively common. It is widely used in various engineering projects, house construction and building decoration. Its fracture will always be found in the production, manufacturing and key marketing of alloy pipe, That is, many stages of production and processing are not done well. Another is that the seasoning is not enough and the proportion of chemical molecules is wrong. There are all reasons.Ashburn, Peak crackAll the cracks occur at -mm away from the edge below the alloy pipe, and the macroeconomic orientation is vertical to the cold rolling orientation, showing a 'high mountain' shape.b. The professional two-sided arc welding processing technology can complete the electric welding at a good position, which is not easy to have the disadvantages of staggered joint, welding deviation and incomplete penetration, and it is very easy to manipulate the welding quality.