Sign in perhaps register 。

I-beam is widely used in buildings or other metal structures.When selecting I-beam in structural design reasonable I-beam shall be selected according to its mechanical properties, chemical properties, weldability and structural size.IraclionGalvanized pipe is a kind of light thin-walled steel pipe with hollow square section, also known as steel cold-formed profile. It is a section steel with square section shape and size, which is made of Q hot-rolled or cold-rolled strip or coil as the base material, cold bending and high-frequency welding. In addition to wall thickness thickening, the corner size and edge flatness of hot rolled extra thick wall galvanized pipe reach or even exceed the level of resistance welding cold formed galvanized pipe. Hot stamping. Fix the plan product workpiece or preformed vacancy on the rotating journal, with the wheel working pressure vacancy, radial wheel. After one or several solutions, there can also be a variety of methods for the whole process of hollow thick wall rotating body products. Products manufactured by high-precision processing method have excellent physical properties, specification scope, mold shell and software requirements, which are very simple, and relatively low product cost. The processing time is not long enough, the total length of processing pipeline is limited, and the size of machinery and equipment is generally short.Zaslawye,C - section steel is reliable and stable in stress, can be accurately positioned, and is resistant to impact and vibration Moreover, it has good versatility and combination, and has a variety of C-section steel and size selection to ensure its flexibilityKey technical characteristics of alloy pipe:The general alloy pipe with improved performance is variable and has high application value. The alloy pipe contains more Cr and is heat resistant Low temperature resistance Corrosion resistance. There is no aluminum alloy in plain carbon seamless steel pipe, not very little aluminum alloy,IraclionHow much is the I-beam of 14 per meter, and the alloy pipe is used in crude oil Aerospace Chemical plant Power engineering heating furnace. Because the physical properties of alloy tubes are easy to change and adjust.

Application characteristics of I-beam Quality requirementsThe sodium cyanide passivation treatment of alloy pipe can be divided into four categories. Before passivation treatment, the surface of alloy pipe shall be clear of oil stains, pickled and passivated. Passivation treatment can be carried out only after the surface is cleaned and the workpiece of alloy pipe products can be infiltrated into aqueous solution. The passivation treatment of the alloy tube in sodium cyanide transforms the surface layer into a very thin passivation treatment film, which determines that the color of the surface layer has no change before and after passivation treatment, and the reproducibility of the solution is good.equipment maintenance ,The utility model has the advantages that the axial force of the roll is small the axial movement is small, the working inclined plane is not required, the pass occupies a small length of the roll body, and more passes can be matched under the condition of a certain length of the roll body.Stages needing attention in the production and manufacture of alloy tubes→ the two surfaces of the flange are parallel to each other, making it easy to connect, process and install.

Advantages of using I-beam: reduce maintenance cost, reduce downtime, reduce wear, reduce equipment capacity and increase power consumptionLatest consultation, Hot stamping. Fix the plan product workpiece or preformed vacancy on the rotating journal, with the wheel working pressure vacancy, radial wheel. After one or several solutions, there can also be a variety of methods for the whole process of hollow thick wall rotating body products. Products manufactured by high-precision processing method have excellent physical properties, specification scope, mold shell and software requirements, which are very simple, very easy to be replaced, and relatively low product cost. The processing time is not long enough, the processing capacity is not high, the total length of processing pipeline is limited, and the size of machinery and equipment is generally short.Reinforcement mesh is manufactured by automatic and intelligent production line under the strict quality control of the factory. Grid size, so it has good bonding and anchorage with the concrete,IraclionPrice of 15CrMoG seamless pipe, and the load is evenly distributed, which obviously shows the seismic crack resistance of the reinforced concrete structure. The small length of repair welding is mm; The raw material shall not exceed mm after grinding by welding edge.Iraclion,Aiming at the connective tissue and texture produced in stainless steel plate Position and other crystal defects are generally removed by heat treatment processes such as quenching or quenching. The effect of quenching is to optimize the crystal, eliminate structural defects, reduce strength, improve plastic deformation, and also conducive to cold drawing. In the production and manufacture of cold drawn alloy pipe, quenching machinery and equipment cannot be lacked. Therefore, the formulation of appropriate annealing process is a necessary condition to ensure that the alloy pipe mechanism meets the standard and the commodity does not crack. If the manufacturer in order to better one sidedness, reduce the product cost and reduce the quenching process, it will eventually lead to bad harm to the product quality.Application characteristics of I-beam:Application characteristics of I-beam: