Sign in perhaps register 。

　　 Then unscrew the nut at the front end of the pump shaft, remove the cover plate, the pump and motor operate in a coaxial whole. When it runs,sesameWQ submersible sewage pump, the motor shaft will drive the impeller of the pump to rotate, and then at this time, the rotating force can be brought to the medium, so thatsesame,　　The motor burns out the winding due to heat dissipation. The water pump shall be lifted and lowered at any time with the change of water level in the well. In case of water reduction or interruption, the cause shall be found out immediately or the pump shall be shut down for inspection. The cable shall not rub against the shaft wall to prevent the well water from penetrating into the motor along the cable core after the cable is worn.　　Fourth, flow, dust, motor power, impeller speed, pumping rate, maximum particle and weight.Oklahoma-City,　　Vertical slurry pump is an early product. Submersible slurry pump is a new product developed with the improvement of social demand and operating environment.　　Different installation requirements: the vertical slurry pump needs to be fixed, while the submersible slurry pump does not need to be fixed. It can directly invade into the liquid for operation.　　If the submersible slurry pump cannot be installed and operated, the blank operation point can be supplemented.

　　In order to make the equipment perform better when it is used, but this also needs to be based on its working principle. It can not be adapted at will when it is optimized.　　That is, first, check whether the alarm unit has leakage and overheating alarm signals; third, check whether the vibration of the guide rod is normal; fourth, record the flow and current of the water pump operation. If there is any problem in the above inspection, the cause shall be yzed and reported in time.　　Troubleshooting: first increase the water pressure, then inject water into the pump body, and then start the pump. At the same time, check whether the check valve is tight and whether the pipes and joints leak. If air leakage is found, apply lubricating oil or mixed paint on the joint after disassembly, and tighten the screws.Quality recommendation,sesameScrew deep well pump,　　The equipment is integrated with the oil cooler, with compact layout. The water pump meets the modular and integrated design requirements of diesel engine parts. The joint surface with oil cooler adopts rubber sealing method which has good sealing effect. Submersible slurry pump is a kind of solid-liquid mixing medium with the help of centrifugal force　　Second, the service life of the flow passage parts of the pump is relatively long, saving production costs.　　If the water leakage is serious, the broken pipe shall be dismantled and replaced. Lower the lift and press the nozzle of the water pump into the water for .m.

　　The installation of submersible slurry pump is a step that needs to be concerned. Since we all care about it, it is mainly because the installation will directly affect the use effect. The installation work should be seamless. Some key operating points can be seen when installing the slurry pump.The cost is reasonable,　　Most of the time, we don&#;t know how to choose the pump when we buy it. In fact, we only need to choose the appropriate equipment according to our own use needs when we choose it. It&#;s more like that in a conventional family, when we use it, the flow is small　　Slide evenly and slowly along the guide rail until the active coupling is in place. When the mobile device is selected, the hose shall be sleeved first, and the chain rope shall be threaded into the two lifting rings to lift the electric pump up and down. Be careful not to use the cable as a rope to avoid danger.　　It generator and market formed at the beginning of construction have gradually formed a certain scale after more than ten years of rapid development. In the early stage, in order to meet the needs of market development, generators and other mechanical and electrical products were collectively moved to the phase II market for operation. With a good business environment, water pumps and generatorssesame,　　The Tao part also consumes part of it.　　There is a difference between submersible slurry pump and sewage pump. Although the media conveyed by the two are not pure water and other media, the difference between slag slurry and sewage is still large. Let&#;s take a look at the difference between the two.　　Basically,sesameZD slurry pump, the reasons for the motor heating of the submersible slurry pump are the above items. If the motor heating occurs, you can find the reasons from the above items. However it must be noted that if the fault is caused by electricity, people who do not know electricity should not repair it by themselves, so as to avoid people