Sign in perhaps register 。

　　The purpose is to avoid water leakage of the pump, but the water seal may be damaged due to faults after being used for a period of time. Let&#;s learn how to replace the water seal.　　This phenomenon shows that the failure of the pump is not only a material problem, but also reminds the pump designers and producers that in addition to good working conditions, high reliability and long service life. The pump shall be designed in addition to the conventional design method of fluid mechanicsLong live water　　The bearing is worn and bent.　　The water pump can be used to transport and pressurize clean water without impurities, such as apartment, residence villa water supply, factory water supply, drinking water system and water treatment. In short, there are many uses.Iganga,　　 First of all, let&#;s understand the causes of insufficient liquid supply: If the liquid level stored in the circulating liquid storage tank is lower than %, then insufficient liquid supply will occur when it is in use. Or the pump adds too much lubricating oil, which leads to accumulation　　It is not correct that it has no effect on us.　　The balance ring is also disassembled; Then remove the last stage impeller and the key back, and the middle section including the guide vane; in addition, remove the impellers, middle sections and guide vanes at other levels in the same way until the submerged slag slurry

　　Adjustment. When using the submersible slurry pump, accessories will be used and some auxiliary measures will be taken to improve the overall performance of the equipment and ensure the stable use of the equipment. Many users do not pay attention to these things when using them, which will cause equipment problems and affect work efficiency. So we&#;re using　　 Pipeline high-temperature oil pump, pipeline high-temperature chemical pump,Long live waterVertical slurry pump, pipeline high-temperature hot water pump. These models are designed to be formed on the basis of adding water cooling units,Long live waterQuotation slurry pump, and the operating temperature can be as high as degrees or higher.　　 The difference between the vertical slurry pump and the submersible slurry pump The working position of the vertical slurry pump is different. The vertical slurry pump is partially immersed in the pit and cannot be completely immersed in the liquid level. The submersible slurry pump can be completely immersed (including the motor part) below the liquid level; Use of motor for vertical slurry pumpoffer,　　 When adding lubricating oil to the pump at ordinary times, the metering must be controlled, and the excess lubricating oil in the pump must be discharged and replaced regularly.　　What?　　There are differences.

　　 Moreover, the processes of these two pumps are also different,Long live waterDouble suction slurry pump, and the sewage pump can generally be adjusted. Submersible pumps are generally used in some special or other places.Range,　　 the front and rear bearing glands are equipped with oil seals, which are padded with green paper or asbestos. There is a gap of .- mm between the rear gland and the bearing.　　How to prolong the service life of the submersible sewage pump Replace the sealing ring: after long-term use in the sewage medium, the gap between the impeller and the sealing ring may increase, so it should be replaced in time.　　Submersible slurry pump it fills the gap in the application of slurry pump. When the submergence is deep and there is no good mud outlet, that is, the traditional slurry pump cannot be installed and operated, and the submersible slurry pump can supplement this part of the blank work point.Long live water,　　 The pump body (can not) bear the pressure from the outlet pipeline system. The standby pump in the warehouse should rotate (/ times a week to make the shaft bear the load and external vibration evenly. The belt CR drive is that the motor is on the (right) side of the pump from the inlet of the pump.　　Function of shaft seal of submersible slurry pump: the main of shaft seal is to prevent high-pressure liquid from leaking out of the pump and prevent air from entering the pump.　　Will be scrapped. In addition, since the length of the long shaft is generally fixed, the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. The submersible slurry pump is developed to adapt to increasingly complex working conditions and facilitate the use of users. Its use mode is more