Sign in perhaps register 。

　　 Cutting blades can be selected to cut some large block solid substances into pieces during use, so that blockage can be avoided during reuse.　　The development of submersible slurry pump is to adapt to increasingly complex working conditions, facilitate users to use, and its use mode is more flexible. And it fills a part of the gap in the application of slurry pump. When the submergence depth is deep and there is no better slurry outlet, that is, in the traditional slurry pumpJurmara,　　Suction lift refers to the distance within the suction depth at the inlet of the pump when there is water in the inlet pipeline but there is no positive pressure at the inlet (quantifier, in length). In fact, all centrifugal pumps have suction head, but the length is different. In a word, those with higher head have suction head　　During adjustment, firstly loosen the support cover, then compress the nut, tighten the compression nut of the bearing seat evenly to make the assembly move towards the pump head. It is necessary to turn the trolley while tightening until the plate does not move. Rotate according to the pump operationNeyagawa,　　When the submersible slurry pump is used at ordinary times, cavitation usually occurs, which has a great impact on the impeller of the equipment itself. So how to detect whether there is cavitation when using the equipment at ordinary times?　　The first stage impeller of the pump is disassembled; It is also necessary to screw down the connecting nut between the water absorption section and the bearing body and the bolt on the bearing pressure connection, so that it is convenient for us to disassemble the bearing parts; When the shaft is pulled out from the suction section, the fixing nut on the shaft shall be　　Superior, complete protection s,JurmaraDrilling fluid slurry pump, reasonable structure convenient installation and high cost performance. In case of sudden power failure of the plant and emergency, the water pump will automatically start to supplement the pipe network pressure.

　　 First remove the pump from the engine.　　Slide evenly and slowly along the guide rail until the active coupling is in place. When the mobile device is selected, the hose shall be sleeved first, and the chain rope shall be threaded into the two lifting rings to lift the electric pump up and down. Be careful not to use the cable as a rope to avoid danger.　　 During the installation of smooth bearing components, if the installation is correct the smooth oil is appropriate, the repair is timely, and the delivery life will be long, the repair personnel should regularly repair the bearing components, check the condition of the bearings and the smooth oil,JurmaraCarbon steel explosion-proof pipeline pump, and regularly add or replace the smooth oil during the work, and the interval and writeInformation recommendation,　　During normal operation, the temperature of the motor is very high, it is easy to burn the motor and replace it with a new one. In fact, one motor burns out at this time. Don&#;t worry about replacing it. You must find out the cause of the motor&#;s heating, or　　Basically, the reasons for the motor heating of the submersible slurry pump are the above items. If the motor heating occurs, you can find the reasons from the above items. However, it must be noted that if the fault is caused by electricity, people who do not know electricity should not repair it by themselves, so as to avoid people　　At present, mechanical seals occupy an increasing share in the slurry pump seal market.

　　 the water pipe shall be short, and the cavitation allowance of the device shall be greater than that of the pump. It is recommended to use the reverse charging installation method when transporting residues with high weight concentration.target,　　The submersible slurry pump can be used to transport a lot of media containing solid particles when it is used at ordinary times, which is quite convenient for installation and maintenance.　　Stability and reliability of seals between pump bodies.Jurmara,　　It, generator and market formed at the beginning of construction have gradually formed a certain scale after more than ten years of rapid development. In the early stage,JurmaraSubmersible sewage pump, in order to meet the needs of market development, generators and other mechanical and electrical products were collectively moved to the phase II market for operation. With a good business environment, water pumps and generators　　The high-pressure water flows to the space occupied by the original bubble at a very high speed, forming an impact force. The metal surface of the pump was fatigued and damaged by these impacts. Cavitation is caused by air bubble rupture and material stamping due to the difference in air temperature and pressure　　 The submersible slurry pump usually relies on water cooling to dissipate heat. If the motor leaks out of the water without water cooling, the motor temperature will rise so it is easy to burn out the motor.