Sign in perhaps register 。

which are wear-resistant

　　The mixing impeller and other main flow passage parts are made of high wear-resistant materials, corrosion-resistant, non clogging and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more thorough desilting. No auxiliary vacuum pump is required and the investment is lower. nothing　　It is an auxiliary means for some on-site monitoring.Valmiera,　　During daily use, we can observe, listen to and touch the submersible slurry pump according to the above methods, so as to judge whether there is a fault and the fault part of the slurry pump, and deal with it in time if any fault is found.　　; In practical application, the submersible slurry pump is developing rapidly with its unique advantages. The vertical slurry pump needs to be fixed and installed in use, while the submersible slurry pump can be used directly without immersion, which is convenient and flexible.Menzel Bourguiba, the sealing of the equipment can not bear the water pressure at this depth.　　 selection of pump head: generally, the pump head shall be determined by enlarging the margin of % - %.　　Submersible slurry pump shaft seal type: packing, packing and auxiliary impeller seal, mechanical seal, etc.

　　Adjustment. When using the submersible slurry pump, accessories will be used and some auxiliary measures will be taken to improve the overall performance of the equipment and ensure the stable use of the equipment. Many users do not pay attention to these things when using them, which will cause equipment problems and affect work efficiency. So we&#;re using　　 Pipeline single-stage single suction hot water pump. It is an IRG type single-stage single suction hot water pipeline pump with ring conveyor belt for high-temperature hot water boilers in metallurgy, chemical industry, paper mills, timber, restaurants, textiles, bathrooms, hotels and other departments. The operating temperature is generally not more than ℃.　　What is the solution to this situation?project,　　Discount. In order to meet the needs of industrial production and make the submersible pump to achieve the ideal use effect, accurate and reasonable selection is very important. In order to select the pump reasonably and correctly, the following aspects need to be considered: Selection of shaft seal form: shaft seal of submersible slurry pump　　Line direction pay attention to the direction of rotation. Then loosen the original compression nut of the bearing box of the slurry pump of the submersible pump, tighten the adjusting screw of the bearing box evenly, and then move the rotor assembly towards the motor. Then it is necessary to check the clearance with a feeler gauge δ, When δ= A (. ~ mm　　If the water leakage is serious, the broken pipe shall be dismantled and replaced. Lower the lift and press the nozzle of the water pump into the water for .m.

　　Occurrence of personal injury accident. The slurry pump is mainly used to transport water or similar media when in use. It can also be regarded as a common pump in our life,　　The production department has to spend a lot of money to maintain and update the pump every year. The pumps made of cast iron, bronze, rubber lining, stainless steel,ValmieraSplit vertical pipeline pump, titanium alloy and other materials used in China&#;s mining, chemical and water conservancy projects on the Yellow River are prone to wear, short service life and many faults　　In this way the upper guide housing is installed in turn. After the pump is installed,ValmieraRubber lining submerged slurry pump, pull the pull nut, take out the gasket tighten the pull nut evenly, and then rotate the electric pump from the coupling. The rotation must be uniform.　　Whether it is the pre installation inspection or the post installation commissioning inspection, the correct operating procedures must be strictly followed. Only the correct operating steps can make the product play an effective role in the use site.Valmiera,ValmieraWater well pipeline pump,　　 A trash trap can be added at the position of the water inlet pipe and used at an angle of degrees, and then a filter screen is installed in the trap to filter impurities for the second time, so as to avoid the blockage of the submersible slurry pump during use.　　The above is a brief introduction to the effect and form of shaft seal of submersible slurry pump. Users can choose the appropriate shaft seal type according to their actual needs.　　When the pump is not in use, the pump shall be lifted away from the water source in time to drain the accumulated water in the pump