Sign in perhaps register 。

After : on October , continue to implement the measures of stopping and limiting production specified in TZBZ [] No. document. All sintering machines and shaft furnaces using wet desulphurization in iron and steel enterprises in the city were shut down, and sintering machines using semi dry desulphurization continued to be shut down for %. The access of vehicles is alicted. The port collection and distribution vehicles are prohibited from entering and leaving the port area. The city s steel, coking, electric power, cement, the vehicle enterprises in the above industries will implement % of the peak load shifting emission reduction measures. It is estimated that the average daily consumption of sintering powder in Tangshan will be more than yuan, and the purchase of iron ore may still maintain a small amount of prudence. In addition,DelagBronze tube, due to the influence of industrial users & amp; quot; coal to gas& quot;, the recent performance of coke is weak. Therefore, in terms of steel plant production, the support of raw materials is weak.Extrusion method: This production method is to cast copper ingots after smelting, and extrude copper tubes by large extruder after secondary heating.Delag,Many people do not fully understand the storage method of copper tubes in the process of use and production methods.Disadvantages: Due to loose tissue and high pressure resistance, the pipe is only used to produce small air conditioning copper rods.Joal-Fadiout,Red copper inventory in key areas has risen continuously, but the total pressure is not big. From the current overall inventory situation of the main distribution centers Wu an, Jiangyin and Lecong, the inventory level remains relatively moderate, and the pressure on the market is relatively small. In Wu an market, according to the data, as of May , the total inventory of medium and thick plates in Wu an was close to tons, increasing by tons on a weekly basis. In late April, it reached tons lower in the year, it should be said to maintain a relatively moderate level.The ex factory price of Linyi Pipe Factory has decreased by yuan for cash Baocheng ( * mm and rose for three consecutive weeks. In terms of the ovquantity, the same below) yuan, yuan for Jin Zhengyang yuan, yuan for Ruigang Lianlian, yuan for Baoda yuan, yuan for Meixin yuan, and yuan for Taizong yuan.Strong connection firmness of copper pipe: the connection between copper pipe and copper fittings is strong.

Extrusion method: This production method is to cast copper ingots after smelting, and extrude copper tubes by large extruder after secondary heating.How to preserve the copper tube? In order to protect the excellent performance of copper pipes from the impact of the environment, we need to do the following: First, select appropriate sites and warehouses, and keep the surrounding environment dry and ventilated. Do not stack together with acid, alkali, salt, cement, etc.Copper tube is a kind of nonferrous metal tube, which is pressed and drawn seamless tube. The copper pipe has good thermal conductivity, so it becomes the first choice for modern contractors to install the water pipe, heat supply pipe and refrigeration pipe in all residential commercial houses.Where can I find it?,In terms of steel billets: at :, some steel billets in Changli were reduced by , and the current carbon square billets were delivered with tax of yuan. After the th National Congress of the Communist of China, the market had doubts about the uncertainty of environmental production restriction and was still waiting for a clearer direction. Therefore, it can be seen that at this stage, there was no unilateral market for either futures or cash, and there was no definite pattern of ups and downs. According to the monitoring data of Lange Iron and Steel s cloud business platform, as of the time of publication, Tianjin Youwelded Line: the steel mill reported: Rongcheng # yuan/ton, B yuan/ton; Jiujiang # - # to Tianjin yuan/ton; The arrival price of Xinji Aosen # is yuan/ton, and that of B steel is yuan/ton; Jiyuan # yuan/ton, B steel yuan/ton; Fulen # yuan/ton; Weigang # yuan/ton, B steel yuan/ton.To sum up,Delag201 stainless steel plate, the market in Northeast China is generally pessimistic based on the medium and long-term policies and the general environment, as well as the current inventory level in Shenyang. The low inventory level of copper platoon makes the whole market lack of motivation. The copper bar market in this city has stopped this year, and it is hard to improve in the short and medium term. On the whole, the market price of Shenyang copper bars may be stable tomorrow.It is said that due to the optimistic future and tight resources, some iron plants do not take orders temporarily. The steel mills in Liaoning have increased their enthusiasm for purchasing steel. The iron mills have delivered well, and the price of raw materials has risen, so the iron price has risen. The iron mills have a high enthusiasm for producing steel, so there is not much cast iron resources, and the price has risen. A few steel mills in Tangshan began to purchase a small amount of steel for smelting, and most steel mills are still on the lookout for inquiry. Under the background of increasing cost and gradual release of demand, the pig iron market is performing well and is expected to continue to operate strongly in the short term.

In Jiangyin market, another distribution center, the overall inventory of the current circulation link is about tons, slightly lower than the normal level. At the beginning of this week, the price gap between Jiangyin prices and those in the north has also been able to correspond to the slightly lower circulation inventory. However, from the perspective of the policy port of the steel plant, the overall production situation of Nangang, Hengrun, Dada, etc. is relatively normal, and the amount of resources in the later period remains stable. The overall inventory of Lecong market remains at about to tons which is a medium normal level,The production method of soft copper tube is basically the same as that of hard copper tube, that is, the annealing process is added compared with the hard copper tube. Annealing of copper tubes means that they are calcined in a high temperature furnace to change the arrangement of the elements in the copper tubes. However,Delag321 stainless steel coiled plate, after annealing, the copper tubes will become soft, which makes it easier to bend. The copper tubes produced in this way are called soft copper tubes.As the inner wall of the pipe rubs with water, the greater the flow resulting in erosion corrosion. The higher the water pressure, the welding flux must have a degree of corrosivity continue to heat the joint and try again. The melted filler metal is sucked into the casing port according to the capillary effect until a complete filler metal ring appears on the casing port. Remove the flame Pay special attention not to let the flame directly contact the filler metal. It should be the heat at the joint that melts the filler metal. In order to clean the copper pipe, and shall be cleaned after brazing. The so-called & quot; self-cleaning& quot; fluxes are generally not recommended because of their corrosivity.Delag,The market price of Zhengzhou copper bars is basically stable, and the shipment is not good. In terms of tube blank: today, Shandong Luli tube blank slightly reduced by yuan, and the current mainstream ex factory price is - yuan. In terms of pipe plant: Linyi Pipe Plant locked the price for a week. With a stable market mentality the factory price of hot rolled seamless pipes is now between - yuan. On the market side: with the arrival of the off-season, traders generally ship goods at a high price. Replenishment is mainly to maintain the existing inventory, and there is no large replenishment plan. The demand is sluggish, and the market price of Zhengzhou copper bar is expected to be stable and declining.Advantages of red copper tube Durability: copper has stable chemical properties, integrating cold resistance, heat resistance, pressure resistance, corrosion resistance and fire resistance and can be used in different environments for a long time.When welding, just add enough filler metal to fill the capillary gap. Too much filler metal will only form a ball at the bottom of the joint or run into the pipe.