Sign in perhaps register 。

due to the falling off of the oxide scale of the galvanized square pipe

When sand blasting or manual mechanical derusting is used the metal on the surface of the galvanized square pipe is directly exposed in the air. If a primer is not applied in time, the surface of the galvanized square pipe is easy to rust again, affecting the adhesion of the paint film. I am engaged in all kinds of square tubes, square rectangular tubes, seamless square tubes,PetropolisPicture of galvanized square pipe, galvanized square tubes, galvanized tubes and other materials all year round. I operate in good faith. Welcome to call! As the paint is a time-effective material, the overstock of inventory is easy to expire. Therefore, the main indexes of the paint must be rechecked before use, and the paint can be used only when the results meet the standards.Fatigue strength, plasticity and hardness discussed above are indicators of the mechanical properties of metals under static load. In fact, many machine parts work under cyclic load, under which fatigue will occur.Petropolis,The strip caused by component segregation, that is, when the steel contains harmful impurities such as phosphorus and is pressed and delayed, the impurities elongate along the rolling direction. When the steel is cooled below ,PetropolisGalvanized steel prices today, these impurities become the core of ferrite, making the morphology of ferrite distributed in bands,Compared with other welding, square pipe welding has many advantages mainly because of the exothermic reaction, the material only needs to be heated below the melting pointMain uses of square tube: square tube is mainly used in tap water engineering, petrochemical industry, chemical industry, electric power industry, agricultural irrigation and urban construction. It is one of the key products developed.C. special performance steel: (a) stainless and acid resistant steel; (b) Heat resistant steel; (c) Electric heating alloy steel; (d) Electrical steel; (e) High manganese wear resistant steel.

Improve the positioning and pre bending steps, if necessary, to ensure that the web hunting problem does not occur when pressing parts. Change the shape of the surface pressure of the material to ensure the quality of the parts and avoid the non movement of the surface shape of the roll gap, resulting in uneven walking feeding.High hardness square tubes mainly bear fatigue load, so they must have high hardness. Therefore quenching, surface quenching or chemical heat treatment shall be carried out, followed by low-temperature tempering treatment.Stage ( & mdash; )Quality risk,B. spring steel C. bearing steel tool steel: A. carbon tool steel; b. Alloy tool steel; c. High speed tool steel.Square pipe for conveying flammable and non flammable fluids, Standard No.: gbt (gbt - ). The representative material is l-l pipeline steel. It is mainly used to transport flammable and non flammable fluids. Low pressure or high pressure square pipes have high requirements. The purpose of large-diameter qb square pipe is qb square pipe, C-shaped steel and H-shaped steel. It is mainly used in the construction of simple plant, steel structure and other infrastructure. Qb square pipe is generally used as the frame and purlin of the plant. C-shaped steel Steel is an important support for the plant, and H-section steel is used as load-bearing. Especially in recent years, a large number of small and medium-sized enterprises have started to build spacious and bright plants. If traditional buildings are built, the time is slow, and the investment is large. For some small and medium-sized enterprises, if the investment in the plant is too high, the capital will be produced after operation Serious impact. The plant built with qb square tube, money saving and fast use. Therefore, the sales of qb square tube, C-section steel and H-section steel have increased significantly in recent years and become the first choice for plant construction. Qb square tube C-section steel and H-section steel are mainly used in the construction of simple plant, steel structure and other infrastructure The qb square tube is used as the frame and purlin of the plant. The C-shaped steel is used as the important support of the plant, and the H-shaped steel is used as the load-bearing. Especially in recent years, a large number of small and medium-sized enterprises around the country have started to build spacious and bright plants. If the traditional buildings are built, the time is slow, the work progress is affected, and the investment is large. For some small and medium-sized enterprises Said that if the investment in the plant is too high, it will have a serious impact on the capital after operation. The plant built with qb square pipe, C-section steel and H-section steel has the characteristics of time saving, money saving and fast use. Therefore, the sales of qb square pipe, C-section steel and H-section steel have increased significantly in recent years, becoming the first choice for plant construction. Large diameter qb square pipe plant is introduced Shao measures for effective wrinkle of seamless square pipe: check the wrinkle state, even when the wrinkle around the part is determined to be less than the clamping force, it should be increased to increase the inner diameter of the inner plate and the tensile stress of the wrinkle drawbead. Adopt the principle of loosening after tightening to loosen after tightening and ask Question.Stage ( & mdash; )

Principle of cold drawing strengthening: the lattice defects of steel increase during plastic deformation, and the serious distortion of defect lattice will hinder the progress and slip of lattice, so the yield point of steel increases and the plasticity and toughness decrease. Due to the internal stress in plastic deformation, the modulus of steel decreases. The cold drawn reinforcement is stored at room temperature for ~ d or heated to ~ ℃ and maintained for a fixed time. This process is called aging treatment.Variable cost,The characteristics of square pipe are as follows: the production process of square pipe is simple, the production efficiency is high,Petropolis4 points galvanized square pipe price, the cost is low and the development is fast. The strength of spiral square pipe is generally higher than that of straight seam square pipe. It can produce square pipe with larger pipe diameter with narrow blank, and square pipe with different pipe diameter with blank of the same width. However, compared with straight seam pipe of the same length, the weld length is increased by ~, which will be oriented to the whole country for a long time Individuals and enterprises provide all kinds of square tubes, square rectangular tubes, seamless square tubes, galvanized square tubes, galvanized tubes, on-site settlement, honest operation, local offices, long-term cooperation and low production speed. Therefore, most of the smaller square tubes adopt straight seam welding, and most of the large-diameter square tubes adopt spiral welding.Avoid contact with pollutants such as oil and copper when storing square tubes.. fake and inferior square tubes are easy to fold. Folding is a variety of broken lines formed on the surface of square tubes, and this defect often runs through the longitudinal direction of the whole product. The reason for the folding is that the fake and shoddy manufacturers pursue the rate, the reduction is too large, resulting in ears, folding occurs during the next rolling, and the strength of the square tube will be greatly reduced.Petropolis,Derusting grade for the construction process of epoxy, ethylene, phenolic and other coatings commonly used for square pipes, the surface of square pipes is generally required to reach near white grade (SA). Practice has proved that almost all oxide scale, rust and other dirt can be removed by using this derusting grade, and the depth of anchor grain can reach ~ & mu; m, which fully meets the requirements of adhesion between layer and square pipe The shot derusting process can meet the technical conditions of near white level (SA) with low operation cost and stable and reliable quality.Hot dip galvanized square tube is a kind of square tube which is welded after using steel plate or steel strip to curl and form, and on the basis of this square tube, the square tube is placed in the hot dip galvanized pool and formed through a series of chemical reactions; The production process of hot-dip galvanized square pipe is relatively simple, but the production efficiency is very high and there are many specifications and varieties, but this kind of square pipe needs little equipment and capital, which is more suitable for the production of small galvanized square pipe manufacturers.The general delivery length of qb square pipe is mm-mm, or in the form of interface tube