Sign in perhaps register 。

Patented manufacturing process of I-beam: I-beam has become a new industrial standard for wear-resistant materials The small length of repair welding is mm; The raw material shall not exceed mm after grinding by welding edge.Katadarenia,Seamless pipe is a long steel with hollow section and no joints around it. There are more than production plants under more than companies in more than countries producing seamless pipes, including more than plants under more than companies in countries.The working principle of flat steel finishing machine in I-beam production process is to pre level and finally level the cold flat steel with two groups of leveling wheel sets staggered up and down in the thickness direction; A pair of finishing wheels arranged relatively are used to extrude the width direction so that the width is compressed to achieve the expected parameters, and the compression amount is adjustable; Straighten the width with staggered straightening wheels.LOHA,Patented manufacturing process of I-beam: I-beam has become a new industrial standard for wear-resistant materialsThe specification of I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is cm. The types of I-beam include hot-rolled ordinary I-beam Light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~ mm, expressed as No. ~ No., and the inclination of inner side wall of leg is : The pass system of rolled I-beam includes direct rolling pass system, cross rolling pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.I-beam, also known as steel beam, is a long strip of steel with I-shaped section. I-beam is divided into ordinary I-beam and light I-beam. It is a section steel with I-type section shape.

The specification of I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is cm. The types of I-beam include hot-rolled ordinary I-beam Light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~ mm, expressed as No. ~ No., and the inclination of inner side wall of leg is : The pass system of rolled I-beam includes direct rolling pass system,KatadareniaCustom welded pipe manufacturer, cross rolling pass system and mixed pass system. In addition,KatadareniaWhich galvanized pipe manufacturer is good, I-beam can also adopt special rolling method. Spiral seam submerged arc welded steel pipe (SY- for pressure fluid transportation is a spiral seam steel pipe used for pressure fluid transportation, which takes hot-rolled steel strip coil as pipe blank, often warm spiral forming and welded by double-sided submerged arc welding. The steel pipe has strong pressure bearing capacity and good welding . After various strict scientific inspections and tests, it is safe and reliable to use. The steel pipe has large diameter and high transportation efficiency, and can save the investment in laying pipelines. It is mainly used for transporting oil and natural gas.When selecting I-beam in structural design, reasonable I-beam shall be selected according to its mechanical properties, weldability and structural size.Development Curriculum,Heating surface tubes for low and medium pressure boilers (working pressure is generally not greater than MPA and working temperature is below ℃);Whether I-section steel is ordinary or light because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members.What is the stainless steel passivation of alloy pipe?

Because all parts of I-beam are arranged at right angles,KatadareniaGH3030 superalloy tube, simple construction, cost saving and light structural weight in all directions, and has been widely used. The inner and outer sides of the flange of the I-beam are parallel or close to parallel, and the end of the flange is at a right angle, so it is named parallel flange I-beam. The web thickness of I-beam is smaller than that of ordinary I-beam with the same height of web, and the flange width is larger than that of ordinary I-beam with the same height of web, so it is also named wide edge I-beam.target,What are the uses of I-beam?The use of hot dip galvanizing has expanded with the development of industry and agriculture. Therefore, hot-dip galvanized products have been widely used in industry (such as chemical equipment, petroleum processing, marine exploration, metal structure, power transportation, shipbuilding, etc.), agriculture (such as sprinkler irrigation, heating room), construction (such as water and gas transportation, wire casing, scaffold, house, etc.), bridges transportation, etc. because hot-dip galvanized productsAccording to the national standard of hot rolled H-section steel in China (GB / t-, H-section steel is divided into narrow flange, whose codes are Hz, HK and Hu respectively. Narrow flange H-section steel is suitable for beams or compression bending members, while wide flange H-section steel and H-section steel piles are suitable for axial compression members or compression bending members. Compared with H-section steel, IX and iy are not as good as H-section steel under the premise of equal weight.KatadareniaPrecision cold rolling of small and medium-sized bearing sleeves with alloy tubes can greatly improve material utilization, bearing performance and service life. This paper systematically introduces the development of high quality cold drawn bearing steel pipe and its application in bearing. Precision cold rolling of small and medium-sized bearing sleeves with bearing steel pipes can greatly improve material utilization, bearing performance and service life. This paper systematically introduces the service life of high quality cold drawn bearings. Peak crack Miscellaneous scab