Sign in perhaps register 。

LaucaCorrosive pipeline pump,

　　Do a good job of fixing to avoid the motor falling into the water and directly scrapping.　　The utility and durability of the utility model, so the polymer composite materials are generally used in production.Lauca,　　And multi-stage slurry pump; Fourth, the types of slurry pump can be divided from the pump shell of slurry pump: single shell slurry pump and lecture slurry pump; Let&#;s talk more about the model classification of slurry pumps: such as ah, HH, m slurry pumps. These series of slurry pumps can be collectively referred to as fractional series slurry pumps because these types　　Troubleshooting: first increase the water pressure, then inject water into the pump body, and then start the pump. At the same time check whether the check valve is tight and whether the pipes and joints leak. If air leakage is found,LaucaVertical multistage centrifugal pipeline pump, apply lubricating oil or mixed paint on the joint after disassembly, and tighten the screws.Solenzo,　　When using the sand pump,LaucaHorizontal slurry pump, be sure to pay attention to the steering divergence between the motor and the pump. The sand pump has an arrow on the pump to mark the main steering. After the power supply is connected, run the pump without load. Check whether the motor operates normally. During operation, be careful not to exceed the bearing on the pump support to avoid　　During the process, the equipment must be regularly maintained and overhauled to avoid blockage. As the name suggests, but in fact, we use it at ordinary times　　With the arrival of midsummer and the intensification of the contradiction between supply and demand of kerosene, the power supply across the country has been tense again, which has driven the hot sale of it and generators in the phase II market. According to relevant data, in the second half of the year, there is still a large gap after China&#;s power balance.

　　During adjustment, firstly loosen the support cover, then compress the nut, and then loosen the bearing seat. After adjusting the screw, tighten the compression nut of the bearing seat evenly to make the assembly move towards the pump head. It is necessary to turn the trolley while tightening until the plate does not move. Rotate according to the pump operation　　Is there an important cf fire control cabinet? Analyze the importance of configuring cf fire control cabinet for everyone.　　 The fixing method of the impeller is changed from screw thread to key clamp to prevent the impeller from falling off and causing damage!Meticulous workmanship,　　 Protective packing of shaft seal the shaft seal pump shall regularly check the sealing water pressure and water volume, keep a small amount of cleaning water flowing along the shaft, check the packing and regularly replace the packing. The shaft seal water pressure and water volume shall meet the above (shaft seal inspection) requirements.　　The motor is scrapped. Moreover, because the length of the long shaft is generally fixed, the installation and use of the pump is troublesome, and the application occasions are subject to many restrictions.　　Submersible slurry pump shaft seal type: packing, packing and auxiliary impeller seal, mechanical seal, etc.

　　Ensure that the service time will be extended when it is used. We all know that the submersible slurry pump needs to optimize its structure to meet the requirements of use because the medium it transports is relatively special. The structure has been optimized toScheme customization,　　What is the cause of pump overload.　　To sum up, we can know that the submersible sewage pump is both a submersible pump and a sewage pump, Ritter pump will provide you with the highest quality slurry pump products; The latest development of submersible slurry pump technology in recent years The diving depth has increased from meters to meters!Lauca,　　A large amount of lubricating oil is stored.　　However there is also a disadvantage of using the auxiliary impeller sealing system, that is, it takes some energy on the auxiliary impeller of the submersible slurry pump, which is generally about %. However, as long as the planning is reasonable this part of the lost flow can be reduced. The slurry pump is mainly applicable to electric power, metallurgy and coal　　Be sure to choose a pump that is more suitable for use.