Sign in perhaps register 。

　　Analysis of installation problems of slurry pump For bearings lubricated with thin oil,Antigo kuscatlandSplit vertical pipeline pump, oil shall be added according to the oil level line of the oil standard before start-up. Add (HL hydraulic oil in winter and (hl hydraulic oil in summer. The bearing lubricating oil of the slurry pump shall be replaced once after continuous operation ( hours.　　So it has a process of water diversion and exhaust. There are usually two ways to inject water into equipment. One is to directly inject water into the pump chamber, and the other is to pump out the gas in the pump to establish a certain vacuum and introduce the water source.Antigo kuscatland, the reaction force of the impeller may directly top the pump shaft. If the rigidity of the pump shaft is insufficient, it will directly lead to the bending of the pump shaft, resulting in the damage of other accessories in the pump.　　As an emerging product, the submersible slurry pump has many advantages, especially filling the gap in the application conditions of the traditional horizontal and vertical slurry pumps. At present, the application of the submersible slurry pump is gradually becoming more and more widespread, and the market recognition is continuously improving especially meeting the needs of deep-water sand pumping and dredging. At present, the depth can reach meters.Banes,Antigo kuscatlandIrrigation deep well pump,Antigo kuscatlandZD slurry pump,　　So it is called: submersible slurry pump.　　 The gas inadvertently entered in the equipment is discharged and good sealing performance is ensured.　　 First, screw down the bolts on the side bearing pressure cap, and then remove the nuts used for the connection between the three parts: discharge section, stuffing box body and bearing body; Then screw off the round nut on the shaft, and successively install the bearing inner race, bearing gland and retaining sleeve

　　Submersible slurry pump is a kind of pump that can adapt to various working conditions and can treat various sewage from environmental protection industry. Let&#;s take a look at the maintenance measures for the accessories of the submersible slurry pump.　　The working principle of the self-priming pump is to fill the pump casing with water (or there is water in the pump casing itself) before the pump is started. After startup, the impeller rotates at a high speed to make the water in the impeller channel flow to the volute. At this time, a vacuum is formed at the inlet to open the water inlet check valve. The air in the suction pipe enters the pump and　　Rate.How much is it,　　 When starting the slurry pump the outlet gate valve shall be (closed or slightly opened by /. Before starting the slurry pump, slowly start the pump outlet valve. The size and speed of opening the pump outlet valve should be based on the fact that the pump does not vibrate and the motor　　The mixing impeller and other main flow passage parts are made of high wear-resistant materials, which are wear-resistant, corrosion-resistant, non clogging and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more thorough desilting. No auxiliary vacuum pump is required and the investment is lower. nothing　　 one method is to use ultrasonic method to detect whether the equipment has cavitation. This method is often convenient for re detection. Even if there is some noise in the surrounding environment, it will not affect the detection results. Therefore, many pumps tend to have better measurement results when in use.

　　At the same time,　　Troubleshooting: first increase the water pressure, then inject water into the pump body, and then start the pump. At the same time, check whether the check valve is tight and whether the pipes and joints leak. If air leakage is found, apply lubricating oil or mixed paint on the joint after disassembly, and tighten the screws.　　 absorb all kinds of diamond sand, quartz sand, steel slag and water slag solid particles.　　The utility and durability of the utility model so the polymer composite materials are generally used in production.Antigo kuscatland,　　What is the solution to this situation?　　After meters, the sealing of the equipment can not bear the water pressure at this depth.　　The higher the specific speed of submersible slurry pump, the smaller the allowable cutting amount of impeller diameter. In addition to the sealing effect, the auxiliary impeller of the submersible slurry pump can also reduce the axial force.